1.1 RESISTOR.
Kegunaan: Sebagai pembatas arus dan sebagai beban pada rangkaian.
Simbol
Warna Anka Toleransi
Hitam 0
Coklat 1
Merah 2
Jingga 3
Kuning 4
Hijau 5
Biru 6
Ungu 7
Abu-Abu 8
Putih 9
Emas 5%
Perak 10%
Tanpa warna 20%
4 warna
Anka pertama
Anka kedua
Jumlah No
Toleransi
5 warna
Angka pertama
Angka kedua
Angka ketiga
jumlah nol
Toleransi
Rumus :V = IxR
Dimana :V= Besar tegangan pada beban (V).
I= Besar arus yangb mengalir (A).
R= Harga beban (Ω).
Rangkaian Resistor:
Seri: Rtotal = R!+R2+R3.
Parallel:
Rtotal=1/R1+1/R2+1/R3
Selasa, 10 Mei 2011
Menentukan Nilai Resistor Tetap dengan Kode Warna pada Resistor
Untuk menentukan nilai resistor ada beberapa hal yang perlu diingat ;
1. Memahami kedudukan warna-warna tersebut pada resistor tetap.
A, Warna pertama : Untuk menyatakan angka pertama ( digit ke-1 )
B. Warna kedua : Untuk menyatakan angka kedua ( digit ke-2 )
C. Warna ketiga : Untuk menyatakan banyaknya nol atau faktor pengali Atau pangkat dari bilangan 10..
D.Warna keempat : Untuk menyatakan toleransi ; Emas = 5 %, Perak = 10 %
Dan Non = Tak berwarna = 20 % 1
2.Jika Emas berada pada warna yang ketiga, maka faktor pengalinya = 0,1=10
3.Jika Perak pada warna ketiga, maka faktor pengalinya = 0.01 =100
4.Dan yang pentingnya adalah hafal akronim HiCoMeJiKuHiBUAPEPNon
Yaitu 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 5 %, 10 %, dan 20 %
HUKUM OHM
George Simon Ohm telah melakukan percobaan-percobaan dan membuktikan bahwa terdapat hubungan yang erat antara arus listrik ( I ), tegangan listrik ( V ) dan hambatan listrik/Resistor ( R ).Hubungan tersebut dikenal dengan Hukum Ohm
Yang berbunyi :
Dalam suatu rangkaian tertutup ( Closed Circuit ) - R
Kuat arus listrik ( I ), sebanding atau berbanding
lurus dengan tegangan listriknya ( V ), dan ber-
banding terbalik dengan hambatan listriknya ( R ).
Pernyataan tersebut dapat ditulis secara matematis
Keterangan : I = Arus listrik dalam satuan Ampere ( A )
V = Tegangan listrik dalam satuan Volt ( V )
R = hambatan listrik/Resistor dalam satuan Ohm
Untuk memudahkan mengingat Rumus tersebut dapat kita perhatikan segi tiga penghafal berikut :
V Volt
1. I = ——— = Ampere = ———–
R Ohm
V
———
I | R 2. V = I x R = Volt = Ampere x Ohm
|
V Volt
3. R = ——— = Ohm = ———–
I Ampere
Contoh Soal :
1. Sebuah rangkaian dipasang pada tegangan 12 volt, jika hambatannya 60 ohm.
Tentukan besar arus listrik yang mengalir dalam rangkaian tersebut ?
Penyelesaian :
Diketahui : V = 12 Volt
R = 60 ohm
Ditanyakan : I = ?
Jawab : V 12 Volt 1
I = ——- = ————- = ——– = 0,2 Ampere
R 60 ohm 5
1. Pada sebuah rangkaian mengalis arus listrik sebesar 1500 miliAmpere
dan hambatan listriknya 40 ohm. Tentukan besar tegangan yang dipasang
pada rangkaian tersebut ?
Penyelesaian :
Diketahui : I = 1500 miliAmpere = 1,5 A
R = 40 ohm
Ditanyakan : V = ?
Jawab :
V = I x R = 1,5 A x 40 ohm
= 60 Volt
1. Sebuah setrika listrik dipasang pada tegangan 240 Volt, dan arus listrik yang
mengalir pada setrika tersebut adalah 3 Ampere. Berapakah besar hambatan
dari sertika tersebut ?
Penyelesaian :
Diketahui : V = 240 Volt
I = 3 Ampere
Ditanyakan : R = ?
Jawab : V 240 Volt
R = ——— = ————— = 80 ohm
I 3 Ampere
1. Sebuah lampu dipasang pada tegangan 120 Volt, dan hambatannya 400 ohm.
Tentukan berapa besar arus listrik yang mengalir pada lampu tersebut ?
Penyelesaian :
Diketahui : V = 120 Volt
R = 400 ohm
Ditanyakan : I = ?
Jawab : V 120 volt 3 Volt
I = ——— = ————– = ————
R 400 ohm 10 ohm
= 0,3 Ampere
1. Sebuah rangkaian listrik memiliki hambatan sebesar 300 ohm, dan mengalir
arus sebesar 10 miliAmpere. Pada tegangan berapakah rangkaian dipasang ?
Penyelesaian :
Diketahui : R = 300 ohm
I = 10 miliAmpere = 0,01 Ampere
Ditanyakan : V = ?
Jawab :
V = I x R = 0,01 Ampere x 300 ohm
= 3 Volt
1. Antara titik-titik a dan b pada suatu rangkian terdapat resistor/hambatan listrik
2 ohm. Arus yang mengalir dari a ke b adalah 2 Ampere. Jika, potensial di titik
a = 5 Volt. Berapakah potensial di titik b ?
Penyelesaian :
Diketahui : R = 2 Ohm R = 2 ohm
Va = 5 Volt a b
I = 2 Ampere
Ditanyakan : Vb = ?
I 5 V
Jawab :
Va - Vb = I x R
5 V - Vb = 2 x 2
Vb = 5 V - 4 V
Vb = 1 volt
Jadi, potensial di titik b adalah = 1 Volt = 1 V
1. Antara titik a dan b pada suatu rangkaian terdapat resistor/hambatan listrik
4 ohm. Arus yang mengalir dari a ke b adalah 3 Ampere. Jika, potensial di titik a = 24 Volt. Berapakah potensial di titik B.
Penyelesaian :
Diketahui : R = 4 Ohm R = 4 ohm
I = 3 Ampere a b
Va = 24 Volt
Ditanyakan : Vb = ?
Jawab : I 24 Volt
Va - Vb = I x R
24 V - Vb = 3 x 4
Vb = 24 V - 12 V
Vb = 12 V
Jadi, potensial di titik b adalah = 12 Volt = 12 V
DAYA LISTRIK dan SATUANNYA
Daya Listrik adalah usaha listrik dalam suatu penghantar setiap detik.
Pernyataa ini dapat ditulis dengan rumus :
W V x I x t
P = ———- atau P = ————– maka P = V x I
t t
Keterangan : P = Daya listrik dalam satuan Watt
V = Tegangan listrik dalam satuan Volt
I = Arus listrik dalam satuan Ampere
W = Usaha listrik dalam satuan Joule
W = V x I x t
t = Waktu dalam satuan detik atau sekon
Jika kita hubungkan antara Hukum Ohm dengan Daya Listrik maka diperoleh :
2
V V V
1. P = V x I jika I = ——– maka 2. P = V x ——- = ——–
R R R
2
. P = V x I jika V = I x R maka 3. P = I x I x R = I x R
Jadi untuk menentukan besarnya Daya Listrik dapat kita selesaikan dengan menggunakan tiga buah rumus seperti di atas.
Contoh Soal :
1. Sebuah rangkaian listrik dipasang tegangan 110 Volt, jika arus yang mengalir 2
Ampere. Berapa besar daya listriknya ?
Diketahui : V = 110 volt
I = 2 Vmpere
Ditanyakan : P = ?
Jawab : P = I x V = 2 A x 110 V
= 220 Watt
2. Arus listrik yang mengalir pada sebuah lampu 500 miliAmpere, jika hambatannya
100 ohm. Berapakah besar daya listriknya ?
Diketahui : I = 500 mA = 0,5 A
R = 100 ohm
Ditanyakan : P = ?
2 2
Jawab : P = I x R = ( 0,5 ) A x 100 ohm
= 0,25 A x 100 ohm
= 25 Watt
3. Sebuah rangkaian menggunakan daya listrik sebesar 14.400 Watt.Jika tegangan
yang terpasang 240 Volt, tentukan besar arus yang mengalir pada rangkaian ?
Diketahui : P = 14.400 Watt
V = 240 Volt
Ditanyakan : I = ?
P 14.400 Waat
Jawab : P = I x V, maka I = ——— = ——————
V 240 Volt
= 60 Ampere
4, Sebuah lampu dipasang pada tegangan 120 Volt, dan hambatannya 600 ohm.
Tentukan besar daya listriknya ?
Diketahui : V = 120 Volt
R = 600 ohm
Ditanyakan : P = ?
2 2
V ( 120 ) Volt 14.400 Volt
Jawab : P = ——— = —————— = —————–
R 600 ohm 600 ohm
= 24 Watt
5. Sebuah rangkaian hambatannya 7200 ohm dan menggunakan daya listrik
sebesar 18 Watt. Pada tegangan berapakah rangkaian tersebut dipasang ?
Diketahui : R = 7200 ohm
P = 18 Watt
Ditanyakan : V = ?
2
V 2
Jawab : P = ———- maka V = P x R jadi V = P x R
R
V = 18 Watt x 7200 ohm
= 129600
= 360 Volt
Untuk menentukan nilai resistor ada beberapa hal yang perlu diingat ;
1. Memahami kedudukan warna-warna tersebut pada resistor tetap.
A, Warna pertama : Untuk menyatakan angka pertama ( digit ke-1 )
B. Warna kedua : Untuk menyatakan angka kedua ( digit ke-2 )
C. Warna ketiga : Untuk menyatakan banyaknya nol atau faktor pengali Atau pangkat dari bilangan 10..
D.Warna keempat : Untuk menyatakan toleransi ; Emas = 5 %, Perak = 10 %
Dan Non = Tak berwarna = 20 % 1
2.Jika Emas berada pada warna yang ketiga, maka faktor pengalinya = 0,1=10
3.Jika Perak pada warna ketiga, maka faktor pengalinya = 0.01 =100
4.Dan yang pentingnya adalah hafal akronim HiCoMeJiKuHiBUAPEPNon
Yaitu 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 5 %, 10 %, dan 20 %
HUKUM OHM
George Simon Ohm telah melakukan percobaan-percobaan dan membuktikan bahwa terdapat hubungan yang erat antara arus listrik ( I ), tegangan listrik ( V ) dan hambatan listrik/Resistor ( R ).Hubungan tersebut dikenal dengan Hukum Ohm
Yang berbunyi :
Dalam suatu rangkaian tertutup ( Closed Circuit ) - R
Kuat arus listrik ( I ), sebanding atau berbanding
lurus dengan tegangan listriknya ( V ), dan ber-
banding terbalik dengan hambatan listriknya ( R ).
Pernyataan tersebut dapat ditulis secara matematis
Keterangan : I = Arus listrik dalam satuan Ampere ( A )
V = Tegangan listrik dalam satuan Volt ( V )
R = hambatan listrik/Resistor dalam satuan Ohm
Untuk memudahkan mengingat Rumus tersebut dapat kita perhatikan segi tiga penghafal berikut :
V Volt
1. I = ——— = Ampere = ———–
R Ohm
V
———
I | R 2. V = I x R = Volt = Ampere x Ohm
|
V Volt
3. R = ——— = Ohm = ———–
I Ampere
Contoh Soal :
1. Sebuah rangkaian dipasang pada tegangan 12 volt, jika hambatannya 60 ohm.
Tentukan besar arus listrik yang mengalir dalam rangkaian tersebut ?
Penyelesaian :
Diketahui : V = 12 Volt
R = 60 ohm
Ditanyakan : I = ?
Jawab : V 12 Volt 1
I = ——- = ————- = ——– = 0,2 Ampere
R 60 ohm 5
1. Pada sebuah rangkaian mengalis arus listrik sebesar 1500 miliAmpere
dan hambatan listriknya 40 ohm. Tentukan besar tegangan yang dipasang
pada rangkaian tersebut ?
Penyelesaian :
Diketahui : I = 1500 miliAmpere = 1,5 A
R = 40 ohm
Ditanyakan : V = ?
Jawab :
V = I x R = 1,5 A x 40 ohm
= 60 Volt
1. Sebuah setrika listrik dipasang pada tegangan 240 Volt, dan arus listrik yang
mengalir pada setrika tersebut adalah 3 Ampere. Berapakah besar hambatan
dari sertika tersebut ?
Penyelesaian :
Diketahui : V = 240 Volt
I = 3 Ampere
Ditanyakan : R = ?
Jawab : V 240 Volt
R = ——— = ————— = 80 ohm
I 3 Ampere
1. Sebuah lampu dipasang pada tegangan 120 Volt, dan hambatannya 400 ohm.
Tentukan berapa besar arus listrik yang mengalir pada lampu tersebut ?
Penyelesaian :
Diketahui : V = 120 Volt
R = 400 ohm
Ditanyakan : I = ?
Jawab : V 120 volt 3 Volt
I = ——— = ————– = ————
R 400 ohm 10 ohm
= 0,3 Ampere
1. Sebuah rangkaian listrik memiliki hambatan sebesar 300 ohm, dan mengalir
arus sebesar 10 miliAmpere. Pada tegangan berapakah rangkaian dipasang ?
Penyelesaian :
Diketahui : R = 300 ohm
I = 10 miliAmpere = 0,01 Ampere
Ditanyakan : V = ?
Jawab :
V = I x R = 0,01 Ampere x 300 ohm
= 3 Volt
1. Antara titik-titik a dan b pada suatu rangkian terdapat resistor/hambatan listrik
2 ohm. Arus yang mengalir dari a ke b adalah 2 Ampere. Jika, potensial di titik
a = 5 Volt. Berapakah potensial di titik b ?
Penyelesaian :
Diketahui : R = 2 Ohm R = 2 ohm
Va = 5 Volt a b
I = 2 Ampere
Ditanyakan : Vb = ?
I 5 V
Jawab :
Va - Vb = I x R
5 V - Vb = 2 x 2
Vb = 5 V - 4 V
Vb = 1 volt
Jadi, potensial di titik b adalah = 1 Volt = 1 V
1. Antara titik a dan b pada suatu rangkaian terdapat resistor/hambatan listrik
4 ohm. Arus yang mengalir dari a ke b adalah 3 Ampere. Jika, potensial di titik a = 24 Volt. Berapakah potensial di titik B.
Penyelesaian :
Diketahui : R = 4 Ohm R = 4 ohm
I = 3 Ampere a b
Va = 24 Volt
Ditanyakan : Vb = ?
Jawab : I 24 Volt
Va - Vb = I x R
24 V - Vb = 3 x 4
Vb = 24 V - 12 V
Vb = 12 V
Jadi, potensial di titik b adalah = 12 Volt = 12 V
DAYA LISTRIK dan SATUANNYA
Daya Listrik adalah usaha listrik dalam suatu penghantar setiap detik.
Pernyataa ini dapat ditulis dengan rumus :
W V x I x t
P = ———- atau P = ————– maka P = V x I
t t
Keterangan : P = Daya listrik dalam satuan Watt
V = Tegangan listrik dalam satuan Volt
I = Arus listrik dalam satuan Ampere
W = Usaha listrik dalam satuan Joule
W = V x I x t
t = Waktu dalam satuan detik atau sekon
Jika kita hubungkan antara Hukum Ohm dengan Daya Listrik maka diperoleh :
2
V V V
1. P = V x I jika I = ——– maka 2. P = V x ——- = ——–
R R R
2
. P = V x I jika V = I x R maka 3. P = I x I x R = I x R
Jadi untuk menentukan besarnya Daya Listrik dapat kita selesaikan dengan menggunakan tiga buah rumus seperti di atas.
Contoh Soal :
1. Sebuah rangkaian listrik dipasang tegangan 110 Volt, jika arus yang mengalir 2
Ampere. Berapa besar daya listriknya ?
Diketahui : V = 110 volt
I = 2 Vmpere
Ditanyakan : P = ?
Jawab : P = I x V = 2 A x 110 V
= 220 Watt
2. Arus listrik yang mengalir pada sebuah lampu 500 miliAmpere, jika hambatannya
100 ohm. Berapakah besar daya listriknya ?
Diketahui : I = 500 mA = 0,5 A
R = 100 ohm
Ditanyakan : P = ?
2 2
Jawab : P = I x R = ( 0,5 ) A x 100 ohm
= 0,25 A x 100 ohm
= 25 Watt
3. Sebuah rangkaian menggunakan daya listrik sebesar 14.400 Watt.Jika tegangan
yang terpasang 240 Volt, tentukan besar arus yang mengalir pada rangkaian ?
Diketahui : P = 14.400 Watt
V = 240 Volt
Ditanyakan : I = ?
P 14.400 Waat
Jawab : P = I x V, maka I = ——— = ——————
V 240 Volt
= 60 Ampere
4, Sebuah lampu dipasang pada tegangan 120 Volt, dan hambatannya 600 ohm.
Tentukan besar daya listriknya ?
Diketahui : V = 120 Volt
R = 600 ohm
Ditanyakan : P = ?
2 2
V ( 120 ) Volt 14.400 Volt
Jawab : P = ——— = —————— = —————–
R 600 ohm 600 ohm
= 24 Watt
5. Sebuah rangkaian hambatannya 7200 ohm dan menggunakan daya listrik
sebesar 18 Watt. Pada tegangan berapakah rangkaian tersebut dipasang ?
Diketahui : R = 7200 ohm
P = 18 Watt
Ditanyakan : V = ?
2
V 2
Jawab : P = ———- maka V = P x R jadi V = P x R
R
V = 18 Watt x 7200 ohm
= 129600
= 360 Volt
Kamis, 05 Mei 2011
Rabu, 27 April 2011
Jumat, 22 April 2011
Senin, 11 April 2011
Jadwal motogp 2011
Berikut ini Jadwal Lengkap Moto
GP 2011 :
20 Maret, Qatar (Losail)
3 April, Spanyol (Jerez)
24 April, Jepang (Motegi)
1 Mei, Portugal (Estoril)
15 Mei, Prancis (Le Mans)
5 Juni, Katalunya (Katalunya)
12 Juni, Inggris (Silverstone)
25 Juni, Belanda (Assen)
3 Juli, Italia (Mugello)
17 Juli, Jerman (Sachsenring)
24Juli, Amerika Serikat (Laguna
Seca)
14 Agustus, Republik Ceko (Brno)
28Agustus, Indianapolis
(Indianapolis)
4September, San Marino &
Riviera di Rimini (Misano)
18September, Aragon
(Motorland)
16Oktober, Australia (Phillip
Island)
23 Oktober, Malaysia (Sepang)
6November, Valencia (Ricardo
Tormo Valencia)
GP 2011 :
20 Maret, Qatar (Losail)
3 April, Spanyol (Jerez)
24 April, Jepang (Motegi)
1 Mei, Portugal (Estoril)
15 Mei, Prancis (Le Mans)
5 Juni, Katalunya (Katalunya)
12 Juni, Inggris (Silverstone)
25 Juni, Belanda (Assen)
3 Juli, Italia (Mugello)
17 Juli, Jerman (Sachsenring)
24Juli, Amerika Serikat (Laguna
Seca)
14 Agustus, Republik Ceko (Brno)
28Agustus, Indianapolis
(Indianapolis)
4September, San Marino &
Riviera di Rimini (Misano)
18September, Aragon
(Motorland)
16Oktober, Australia (Phillip
Island)
23 Oktober, Malaysia (Sepang)
6November, Valencia (Ricardo
Tormo Valencia)
Minggu, 10 April 2011
IC MN152811TZX
1.+5V
2.FA1
3.SECAM STATUS
4.TUNER CTRL
5.50/60 OUTPUT
6.VIDEO DFT/NOR
7.RST
8.AFC DFT/NOR
9.AUDIA DFT/NOR
10.BAND2
11.CLR KILLER
12.BAND1
13.
14.SIF2
15.SIF1
16.VOL
17.BT DAC
18.VER
19.KEY2
20.KEY1
21.AFC INPUT
22.V SYNC
23.TONE
24.ON/OFF
25.TEST
26.30/60 CH
27.VP
28.NC
29.BLUE
30.H SIYNC
31.BLK
32.GREEN
33.RED
34.RM IN
35.OSC2
36.OSC1
37.SCL
38.SDA
39.50/60 IN
40.STOP IN
41.VP
42.GND
2.FA1
3.SECAM STATUS
4.TUNER CTRL
5.50/60 OUTPUT
6.VIDEO DFT/NOR
7.RST
8.AFC DFT/NOR
9.AUDIA DFT/NOR
10.BAND2
11.CLR KILLER
12.BAND1
13.
14.SIF2
15.SIF1
16.VOL
17.BT DAC
18.VER
19.KEY2
20.KEY1
21.AFC INPUT
22.V SYNC
23.TONE
24.ON/OFF
25.TEST
26.30/60 CH
27.VP
28.NC
29.BLUE
30.H SIYNC
31.BLK
32.GREEN
33.RED
34.RM IN
35.OSC2
36.OSC1
37.SCL
38.SDA
39.50/60 IN
40.STOP IN
41.VP
42.GND
Jumat, 08 April 2011
Tips Mengisi IC MEMORY EEPROM untuk TV Tanpa Programmer OlehDadan Gusramdhan Jumara
IC MEMORY , mungkin itulah yang
akrab di telinga kita ,mari kita
bahas sejenak fungsi dari IC
EEPROM ini
Contoh IC EEEPROM
Berdasarkan kapasitas nya
memory ini biasanya ditulis
dengan nomor 24CXX nah untuk
XX adalah kapasitas nya dalam
Kbit .Contoh 24C08 berarti
kapasitasnya 8 Kilobit ,Di toko
banyak yang jual dengan nomor
24C01,24C02,24C04,24C08,24C16,24c32
NAH yang di jual di toko ini adalah
data nya masih kosong.
Gambar programmer EEPROM
Memory pada pesawat televisi
berfungsi untuk menyimpan data
setting atau konfigurasiSystem
suara ,sistem warna,nicam/
stereo/mono,AV/DVD/SVHS/,
subwoofer atau pun berfungsi
untuk pilihan hardware misalny IC
stereo prosesing ,IC av Switch ,IC
tone contreol ,dllLalu berfungsi
juga menyimpan data Factory
misalnya : white balance,sub
contras,vertikal size,horizontal
wide,pengaturan EW dll.Data
(user adjustment ) atau
pengaturan oleh pengguna
misalnya
volume ,bright,contras ,warna,
bass,treble,program chanel misal
chanel 1 diisi rcti dengn
frekwensi 600mhz dll.
Component documentationIC
numberManufacturerDocumentationAT24C08
Atmel
Web page, Datasheet (PDF)
Component versionsIC
numberPackageCBM part
numberCBM part
descriptionAT24C08 8-pin SOIC
391635-03 IC, EEPROM, 24C08,
PositionsDevicePositionPackageCD³²
U9 SOIC PinoutPinTypeNameSignal
nameCD³²1..2 N/C NC GND 3 Input
A2 GND 4 Power GND GND 5 I/O
SDA Connected to pin 99 of Akiko
6 Input SCL Connected to pin 100
of Akiko 7 Input WP GND 8 Power
VCC VCC
Bagaimana Cara kerja IC MEMORY ?
Pada saat kita menghidupkan
pesawat televisi ,maka IC program
akan mengcopy (membaca) isi
yang ada di IC memory misalnya
vertikal berapa volumenya
berapa ,chanelnya berapa dan
seterusnya.Hal sebaliknya akan
dilakukan pada saat tv nya
dimatikan Dimana data yng sudah
berubah(DIRUBAH OLEH
PENGGUNA) akan disimpan
kedalam IC MEMORY .(writing)
Problem yang sering terjadi
adalah pada saat proses writing
kemudian tiba tiba listriknya
mati ,maka hal ini dapat
menyebabkan kan isi data dari IC
memory ini rusak (data
coruruption) wah ternyata bukan
pejabat saja yang bisa korupsi ic
memory juga bisa korupsi hee
heee
heeeeee……………………………………….
Apakah akibatnya kalau IC si
memory melakukan
korupsi ,tentunya pemerintahan
akan kacau balau ,terjadi
pemogokan dimana mana IC
Stereo mogok ,Tuner juga ikut
mogok ,dan para pejabat lain ikut
mogok dan pemrintahan akan
menyatakan darurat dengan
menyalakan lampu led dan akan
menyatakan kalau negara dalam
keadaan error . Sorry bercanda
soalnya baca nya serius banget
sih ! hehe…..
Pada tv sharp kalau kerusakan di
ic memori biasanya ditandai
dengan TV nyala sebentar terus
mati dengan lampu led blinking
atau kedip.jumlah kedipan nya itu
biasa nya menunjukan part yng
tdk bekerja atau salah setting .
Coba anda bayangkan ketika pada
saat melakukan setting tiba tiba
kita lupa tdk mencatat nilai awal
setting sebelum kita melakukan
perubahan ,sehingga tv nya
menjadi kacau.
TIPS berikut ini adalah bagaimana
caranya menyeting ic memory
agar kembali ke default ,atau ke
posisi standard (standard
setting ).SPAREPARTS YANG HARUS
DISIAPKAN ADALAH IC MEMORY
YANG KOSONG ATAU YANG BARU
BELI DITOKO !Kalau yang udah ada
isi nya kadang tdk berhasil
Saya disini akan memberikan tips
sederhana terutama untuk tv
SHARPUntuk TV sharp adalah
dengan memasang IC MEMORY
yang kosong pada chasis tv ,Lalu
jangan dulu menghidupkan tv
nya .Langkah selanjutnya adalah
menshort kan jumper untuk
service mode sebaiknya di solder
saja kedua jumper nya ,untuk tv
sharp seri wonder atau universe
jumper nya ada dilokasi J122 dan
J124Nah baru setelah itu TV nya
dihidupkan untuk pertama kali
dengan IC memory yang baru
(kosong)tunggu sebentar akan
terjadi proses Writing .Hasilnya
wooow seting default (seting
standard nya) sudah terisi ,lalu
kita tinggal melakukan
adjustment untuk vertikal
saja .Setelah semua OK janga lupa
solderan jumper nya di buka
maning .Bagai mana, anda
mengerti
Untuk polytron Untuk
mengembalikan ke posisi default
mode adalah dengan cara seperti
biasa masuk ke service mode
PolytronStandby duluTekan dan
tahan tombol menu yang ada di
remoteDan untuk mengembalikan
ke setting default adalah 3101
Untuk merk SAMSUNG adalah
dengan cara :Standby dulu
Tekan dan tahan tombol menu
yang ada di remote dengan kode
iniAkan mucul dilayar settingan
Factory modeUntuk
mengembalikan ke setting default
adalah dengan memilih opsi
paling bawah yaitu RESET, ingat
semua data akan tereset kembali
seperti TV baru.Selamat mencoba
Tips dan trik ini hanya berlaku
untuk model tertentu yaitu SHARP
wonder, Universe sedangkan
untuk SAMSUNG hampir semua
tipe bisa, telah dicoba di TV model
20W200,20U200,29UF200.Oya
kerusakan lain yang mungkin
disebabkan adjustmen service
mode ini resiko ditanggung
sendiri yah hehehe….
akrab di telinga kita ,mari kita
bahas sejenak fungsi dari IC
EEPROM ini
Contoh IC EEEPROM
Berdasarkan kapasitas nya
memory ini biasanya ditulis
dengan nomor 24CXX nah untuk
XX adalah kapasitas nya dalam
Kbit .Contoh 24C08 berarti
kapasitasnya 8 Kilobit ,Di toko
banyak yang jual dengan nomor
24C01,24C02,24C04,24C08,24C16,24c32
NAH yang di jual di toko ini adalah
data nya masih kosong.
Gambar programmer EEPROM
Memory pada pesawat televisi
berfungsi untuk menyimpan data
setting atau konfigurasiSystem
suara ,sistem warna,nicam/
stereo/mono,AV/DVD/SVHS/,
subwoofer atau pun berfungsi
untuk pilihan hardware misalny IC
stereo prosesing ,IC av Switch ,IC
tone contreol ,dllLalu berfungsi
juga menyimpan data Factory
misalnya : white balance,sub
contras,vertikal size,horizontal
wide,pengaturan EW dll.Data
(user adjustment ) atau
pengaturan oleh pengguna
misalnya
volume ,bright,contras ,warna,
bass,treble,program chanel misal
chanel 1 diisi rcti dengn
frekwensi 600mhz dll.
Component documentationIC
numberManufacturerDocumentationAT24C08
Atmel
Web page, Datasheet (PDF)
Component versionsIC
numberPackageCBM part
numberCBM part
descriptionAT24C08 8-pin SOIC
391635-03 IC, EEPROM, 24C08,
PositionsDevicePositionPackageCD³²
U9 SOIC PinoutPinTypeNameSignal
nameCD³²1..2 N/C NC GND 3 Input
A2 GND 4 Power GND GND 5 I/O
SDA Connected to pin 99 of Akiko
6 Input SCL Connected to pin 100
of Akiko 7 Input WP GND 8 Power
VCC VCC
Bagaimana Cara kerja IC MEMORY ?
Pada saat kita menghidupkan
pesawat televisi ,maka IC program
akan mengcopy (membaca) isi
yang ada di IC memory misalnya
vertikal berapa volumenya
berapa ,chanelnya berapa dan
seterusnya.Hal sebaliknya akan
dilakukan pada saat tv nya
dimatikan Dimana data yng sudah
berubah(DIRUBAH OLEH
PENGGUNA) akan disimpan
kedalam IC MEMORY .(writing)
Problem yang sering terjadi
adalah pada saat proses writing
kemudian tiba tiba listriknya
mati ,maka hal ini dapat
menyebabkan kan isi data dari IC
memory ini rusak (data
coruruption) wah ternyata bukan
pejabat saja yang bisa korupsi ic
memory juga bisa korupsi hee
heee
heeeeee……………………………………….
Apakah akibatnya kalau IC si
memory melakukan
korupsi ,tentunya pemerintahan
akan kacau balau ,terjadi
pemogokan dimana mana IC
Stereo mogok ,Tuner juga ikut
mogok ,dan para pejabat lain ikut
mogok dan pemrintahan akan
menyatakan darurat dengan
menyalakan lampu led dan akan
menyatakan kalau negara dalam
keadaan error . Sorry bercanda
soalnya baca nya serius banget
sih ! hehe…..
Pada tv sharp kalau kerusakan di
ic memori biasanya ditandai
dengan TV nyala sebentar terus
mati dengan lampu led blinking
atau kedip.jumlah kedipan nya itu
biasa nya menunjukan part yng
tdk bekerja atau salah setting .
Coba anda bayangkan ketika pada
saat melakukan setting tiba tiba
kita lupa tdk mencatat nilai awal
setting sebelum kita melakukan
perubahan ,sehingga tv nya
menjadi kacau.
TIPS berikut ini adalah bagaimana
caranya menyeting ic memory
agar kembali ke default ,atau ke
posisi standard (standard
setting ).SPAREPARTS YANG HARUS
DISIAPKAN ADALAH IC MEMORY
YANG KOSONG ATAU YANG BARU
BELI DITOKO !Kalau yang udah ada
isi nya kadang tdk berhasil
Saya disini akan memberikan tips
sederhana terutama untuk tv
SHARPUntuk TV sharp adalah
dengan memasang IC MEMORY
yang kosong pada chasis tv ,Lalu
jangan dulu menghidupkan tv
nya .Langkah selanjutnya adalah
menshort kan jumper untuk
service mode sebaiknya di solder
saja kedua jumper nya ,untuk tv
sharp seri wonder atau universe
jumper nya ada dilokasi J122 dan
J124Nah baru setelah itu TV nya
dihidupkan untuk pertama kali
dengan IC memory yang baru
(kosong)tunggu sebentar akan
terjadi proses Writing .Hasilnya
wooow seting default (seting
standard nya) sudah terisi ,lalu
kita tinggal melakukan
adjustment untuk vertikal
saja .Setelah semua OK janga lupa
solderan jumper nya di buka
maning .Bagai mana, anda
mengerti
Untuk polytron Untuk
mengembalikan ke posisi default
mode adalah dengan cara seperti
biasa masuk ke service mode
PolytronStandby duluTekan dan
tahan tombol menu yang ada di
remoteDan untuk mengembalikan
ke setting default adalah 3101
Untuk merk SAMSUNG adalah
dengan cara :Standby dulu
Tekan dan tahan tombol menu
yang ada di remote dengan kode
iniAkan mucul dilayar settingan
Factory modeUntuk
mengembalikan ke setting default
adalah dengan memilih opsi
paling bawah yaitu RESET, ingat
semua data akan tereset kembali
seperti TV baru.Selamat mencoba
Tips dan trik ini hanya berlaku
untuk model tertentu yaitu SHARP
wonder, Universe sedangkan
untuk SAMSUNG hampir semua
tipe bisa, telah dicoba di TV model
20W200,20U200,29UF200.Oya
kerusakan lain yang mungkin
disebabkan adjustmen service
mode ini resiko ditanggung
sendiri yah hehehe….
Kamis, 07 April 2011
Selasa, 05 April 2011
TB1227AN
TB 1227 AN
pin1 =VID-IN/SCP-OUT
pin2 =VAGC-FILTER
pin3 =H-VCC [5V]
pin4 =H-OUT
pin5 =CURVE CORRECTION
pin6 =FBP-IN
pin7 =COINCIDENT-DET
pin8 =VDD [5V]
pin9 =SCL
pin10 =SDA
pin11 =DIGITAL-GND
pin12 =B-OUT
pin13 =G-OUT
pin14 =R-OUT
pin15 =TEXT-GND
pin16 =ABCL
pin17 =RGB-VCC [9V]
pin18 =R-IN/DIGITAL
pin19 =G-IN/DIGITAL
pin20 =B-IN/DIGITAL
pin21 =YS-DIGITAL
pin22 =YS/YM/ANALOG
pin23 =R-IN/ANALOG
pin24 =G-IN/ANALOG
pin25 =B-IN/ANALOG
pin26 =COLOR-LIMITER
pin27 =TV/A-IN
pin28 =EXT-A-IN
pin29 =AUDIO=OUT/VSM-OUT
pin30 =APC-FILT
pin31 =Y-IN
pin32 =FSC-GND
pin33 =B-Y IN
pin34 =R-Y IN
pin35 =R-Y OUT
pin36 =B-Y OUT
pin37 =Y-OUT
pin38 =VDD-FSC [5V]
pin39 =BLACK STRETCH
pin40 =X-TAL/16MHZ
pin41 =Y/C-VCC [5V]
pin42 =CHROMA-IN
pin43 =Y/C-GND
pin44 =APL
pin45 =VID-IN/COMPOSIT
pin46 =SDEMO-ADJ
pin47 =TV-IN
pin48 =AFC1-FILT
pin49 =SYNC-OUT
pin50 =V-SEP A
pin51 =SYNC-IN
pin52 =V-RAMP
pin53 =V-OUT
pin54 =V-NF
pin55 =DEF-GND
pin56 =VID-OUT/VBLK-OUT
pin1 =VID-IN/SCP-OUT
pin2 =VAGC-FILTER
pin3 =H-VCC [5V]
pin4 =H-OUT
pin5 =CURVE CORRECTION
pin6 =FBP-IN
pin7 =COINCIDENT-DET
pin8 =VDD [5V]
pin9 =SCL
pin10 =SDA
pin11 =DIGITAL-GND
pin12 =B-OUT
pin13 =G-OUT
pin14 =R-OUT
pin15 =TEXT-GND
pin16 =ABCL
pin17 =RGB-VCC [9V]
pin18 =R-IN/DIGITAL
pin19 =G-IN/DIGITAL
pin20 =B-IN/DIGITAL
pin21 =YS-DIGITAL
pin22 =YS/YM/ANALOG
pin23 =R-IN/ANALOG
pin24 =G-IN/ANALOG
pin25 =B-IN/ANALOG
pin26 =COLOR-LIMITER
pin27 =TV/A-IN
pin28 =EXT-A-IN
pin29 =AUDIO=OUT/VSM-OUT
pin30 =APC-FILT
pin31 =Y-IN
pin32 =FSC-GND
pin33 =B-Y IN
pin34 =R-Y IN
pin35 =R-Y OUT
pin36 =B-Y OUT
pin37 =Y-OUT
pin38 =VDD-FSC [5V]
pin39 =BLACK STRETCH
pin40 =X-TAL/16MHZ
pin41 =Y/C-VCC [5V]
pin42 =CHROMA-IN
pin43 =Y/C-GND
pin44 =APL
pin45 =VID-IN/COMPOSIT
pin46 =SDEMO-ADJ
pin47 =TV-IN
pin48 =AFC1-FILT
pin49 =SYNC-OUT
pin50 =V-SEP A
pin51 =SYNC-IN
pin52 =V-RAMP
pin53 =V-OUT
pin54 =V-NF
pin55 =DEF-GND
pin56 =VID-OUT/VBLK-OUT
TB1240AN
TB 1240 AN
pin1 =AFT OUT
pin2 =A.DE-EM
pin3 =VCC
pin4 =SIF IN
pin5 =IF GND
pin6 =IF IN
pin7 =IF IN
pin8 =RF AGC
pin9 =IF-AGC
pin10 =APC-FILT
pin11 =4.43MHZ
pin12 =Y/C GND
pin13 =YS/YM
pin14 =R IN
pin15 =G IN
pin16 =B IN
pin17 =RGB VCC [5.0]
pin18 =R OUT
pin19 =G OUT
pin20 =B OUT
pin21 =ABL
pin22 =V-RAMP
pin23 =V-NFB
pin24 =V-OUT
pin25 =V-AGC
pin26 =SCL
pin27 =SDA
pin28 =H-VCC [9.1]
pin29 =S-IO/CW-OUT
pin30 =FBP-IN
pin31 =SYNC-OUT
pin32 =H-OUT
pin33 =DEF-GND
pin34 =SCP-OUT
pin35 =E/W-OUT
pin36 =DIG-VCC [9.1]
pin37 =B-Y-IN
pin38 =R-Y-IN
pin39 =Y-IN
pin40 =H-AFC
pin41 =EHT-IN
pin42 =DIG-GND
pin43 =SYNC IN
pin44 =BLK DET
pin45 =C IN
pin46 =Y/C VCC [5.0]
pin47 =IF-DET-OUT
pin48 =LOOP-FILT
pin49 =VCO GND
pin50 =VCO
pin51 =VCO
pin52 =VCO-VCC []
pin53 =SIF
pin54 =RIPPLE
pin55 =SIF/H-PIN
pin56 =FM-DC-NF
pin1 =AFT OUT
pin2 =A.DE-EM
pin3 =VCC
pin4 =SIF IN
pin5 =IF GND
pin6 =IF IN
pin7 =IF IN
pin8 =RF AGC
pin9 =IF-AGC
pin10 =APC-FILT
pin11 =4.43MHZ
pin12 =Y/C GND
pin13 =YS/YM
pin14 =R IN
pin15 =G IN
pin16 =B IN
pin17 =RGB VCC [5.0]
pin18 =R OUT
pin19 =G OUT
pin20 =B OUT
pin21 =ABL
pin22 =V-RAMP
pin23 =V-NFB
pin24 =V-OUT
pin25 =V-AGC
pin26 =SCL
pin27 =SDA
pin28 =H-VCC [9.1]
pin29 =S-IO/CW-OUT
pin30 =FBP-IN
pin31 =SYNC-OUT
pin32 =H-OUT
pin33 =DEF-GND
pin34 =SCP-OUT
pin35 =E/W-OUT
pin36 =DIG-VCC [9.1]
pin37 =B-Y-IN
pin38 =R-Y-IN
pin39 =Y-IN
pin40 =H-AFC
pin41 =EHT-IN
pin42 =DIG-GND
pin43 =SYNC IN
pin44 =BLK DET
pin45 =C IN
pin46 =Y/C VCC [5.0]
pin47 =IF-DET-OUT
pin48 =LOOP-FILT
pin49 =VCO GND
pin50 =VCO
pin51 =VCO
pin52 =VCO-VCC []
pin53 =SIF
pin54 =RIPPLE
pin55 =SIF/H-PIN
pin56 =FM-DC-NF
TB1227DN
TB 1227 DN
pin1 =VID-IN/SCP-OUT
pin2 =VAGC-FILTER
pin3 =H-VCC [5-9v]
pin4 =H-OUT
pin5 =CURVE CORRECTION
pin6 =FBP-IN
pin7 =COINCIDENT-DET
pin8 =VDD [5V]
pin9 =SCL
pin10 =SDA
pin11 =DIGITAL-GND
pin12 =B-OUT
pin13 =G-OUT
pin14 =R-OUT
pin15 =TEXT-GND
pin16 =ABCL
pin17 =RGB-VCC [9V]
pin18 =R-IN/DIGITAL
pin19 =G-IN/DIGITAL
pin20 =B-IN/DIGITAL
pin21 =YS-DIGITAL
pin22 =YS/YM/ANALOG
pin23 =R-IN/ANALOG
pin24 =G-IN/ANALOG
pin25 =B-IN/ANALOG
pin26 =COLOR-LIMITER
pin27 =TV/A-IN
pin28 =EXT-A-IN
pin29 =AUDIO=OUT/VSM-OUT
pin30 =APC-FILT
pin31 =Y-IN
pin32 =FSC-GND
pin33 =B-Y IN
pin34 =R-Y IN
pin35 =R-Y OUT
pin36 =B-Y OUT
pin37 =Y-OUT
pin38 =VDD-FSC [5V]
pin39 =BLACK STRETCH
pin40 =X-TAL/16.2MHZ
pin41 =Y/C-VCC [5V]
pin42 =CHROMA-IN
pin43 =Y/C-GND
pin44 =APL
pin45 =cvbs-in/VID-IN[COMPOSIT]
pin46 =SDEMO-ADJ
pin47 =TV-IN
pin48 =AFC1-FILT
pin49 =SYNC-OUT
pin50 =V-SEP A
pin51 =SYNC-IN
pin52 =V-RAMP
pin53 =V-OUT
pin54 =V-NF
pin55 =DEF-GND
pin56 =VID-OUT/VBLK-OUT
pin1 =VID-IN/SCP-OUT
pin2 =VAGC-FILTER
pin3 =H-VCC [5-9v]
pin4 =H-OUT
pin5 =CURVE CORRECTION
pin6 =FBP-IN
pin7 =COINCIDENT-DET
pin8 =VDD [5V]
pin9 =SCL
pin10 =SDA
pin11 =DIGITAL-GND
pin12 =B-OUT
pin13 =G-OUT
pin14 =R-OUT
pin15 =TEXT-GND
pin16 =ABCL
pin17 =RGB-VCC [9V]
pin18 =R-IN/DIGITAL
pin19 =G-IN/DIGITAL
pin20 =B-IN/DIGITAL
pin21 =YS-DIGITAL
pin22 =YS/YM/ANALOG
pin23 =R-IN/ANALOG
pin24 =G-IN/ANALOG
pin25 =B-IN/ANALOG
pin26 =COLOR-LIMITER
pin27 =TV/A-IN
pin28 =EXT-A-IN
pin29 =AUDIO=OUT/VSM-OUT
pin30 =APC-FILT
pin31 =Y-IN
pin32 =FSC-GND
pin33 =B-Y IN
pin34 =R-Y IN
pin35 =R-Y OUT
pin36 =B-Y OUT
pin37 =Y-OUT
pin38 =VDD-FSC [5V]
pin39 =BLACK STRETCH
pin40 =X-TAL/16.2MHZ
pin41 =Y/C-VCC [5V]
pin42 =CHROMA-IN
pin43 =Y/C-GND
pin44 =APL
pin45 =cvbs-in/VID-IN[COMPOSIT]
pin46 =SDEMO-ADJ
pin47 =TV-IN
pin48 =AFC1-FILT
pin49 =SYNC-OUT
pin50 =V-SEP A
pin51 =SYNC-IN
pin52 =V-RAMP
pin53 =V-OUT
pin54 =V-NF
pin55 =DEF-GND
pin56 =VID-OUT/VBLK-OUT
TB1261N
TB1261N
pin1 =SIF IN/SECOND
pin2 =VCC IF/5V
pin3 =SIF IN
pin4 =SIF IN
pin5 =RF AGC
pin6 =IF IN
pin7 =IF IN
pin8 =IF AGC
pin9 =FM FILTER
pin10 =PIF FILTER
pin11 =X-TAL
pin12 =APC FILTER
pin13 =S FILTER
pin14 =VCC YC/5V
pin15 =R OUT
pin16 =G OUT
pin17 =B OUT
pin18 =YC GND
pin19 =VSM OUT
pin20 =Ysm
pin21 =OSD R
pin22 =OSD G
pin23 =OSD B
pin24 =RGB VCC/9V
pin25 =SCL
pin26 =SDA
pin27 =EHT IN
pin28 =ABCL
pin29 =EW OUT
pin30 =CW OUT
pin31 =DIGITAL VDD/9V
pin32 =SCP OUT
pin33 =H-OUT
pin34 =H AFC
pin35 =H-VCC/9V
pin36 =V-RAMP
pin37 =V-OUT
pin38 =DIGITAL GND
pin39 =Cb OUT
pin40 =Cr OUT
pin41 =Y OUT
pin42 =BLACK DET
pin43 =Y IN
pin44 =Cb-IN
pin45 =Cr-IN
pin46 =C-IN
pin47 =Ys
pin48 =V-IN
pin49 =DC RE
pin50 =DE-EMP
pin51 =VCC IF/9V
pin52 =DET OUT
pin53 =LOOP FILTER
pin54 =FM DC NF
pin55 =SIF OUT
pin56 =IF GND
pin1 =SIF IN/SECOND
pin2 =VCC IF/5V
pin3 =SIF IN
pin4 =SIF IN
pin5 =RF AGC
pin6 =IF IN
pin7 =IF IN
pin8 =IF AGC
pin9 =FM FILTER
pin10 =PIF FILTER
pin11 =X-TAL
pin12 =APC FILTER
pin13 =S FILTER
pin14 =VCC YC/5V
pin15 =R OUT
pin16 =G OUT
pin17 =B OUT
pin18 =YC GND
pin19 =VSM OUT
pin20 =Ysm
pin21 =OSD R
pin22 =OSD G
pin23 =OSD B
pin24 =RGB VCC/9V
pin25 =SCL
pin26 =SDA
pin27 =EHT IN
pin28 =ABCL
pin29 =EW OUT
pin30 =CW OUT
pin31 =DIGITAL VDD/9V
pin32 =SCP OUT
pin33 =H-OUT
pin34 =H AFC
pin35 =H-VCC/9V
pin36 =V-RAMP
pin37 =V-OUT
pin38 =DIGITAL GND
pin39 =Cb OUT
pin40 =Cr OUT
pin41 =Y OUT
pin42 =BLACK DET
pin43 =Y IN
pin44 =Cb-IN
pin45 =Cr-IN
pin46 =C-IN
pin47 =Ys
pin48 =V-IN
pin49 =DC RE
pin50 =DE-EMP
pin51 =VCC IF/9V
pin52 =DET OUT
pin53 =LOOP FILTER
pin54 =FM DC NF
pin55 =SIF OUT
pin56 =IF GND
TB1261N
pin1 =SIF IN/SECOND
pin2 =VCC IF/5V
pin3 =SIF IN
pin4 =SIF IN
pin5 =RF AGC
pin6 =IF IN
pin7 =IF IN
pin8 =IF AGC
pin9 =FM FILTER
pin10 =PIF FILTER
pin11 =X-TAL
pin12 =APC FILTER
pin13 =S FILTER
pin14 =VCC YC/5V
pin15 =R OUT
pin16 =G OUT
pin17 =B OUT
pin18 =YC GND
pin19 =VSM OUT
pin20 =Ysm
pin21 =OSD R
pin22 =OSD G
pin23 =OSD B
pin24 =RGB VCC/9V
pin25 =SCL
pin26 =SDA
pin27 =EHT IN
pin28 =ABCL
pin29 =EW OUT
pin30 =CW OUT
pin31 =DIGITAL VDD/9V
pin32 =SCP OUT
pin33 =H-OUT
pin34 =H AFC
pin35 =H-VCC/9V
pin36 =V-RAMP
pin37 =V-OUT
pin38 =DIGITAL GND
pin39 =Cb OUT
pin40 =Cr OUT
pin41 =Y OUT
pin42 =BLACK DET
pin43 =Y IN
pin44 =Cb-IN
pin45 =Cr-IN
pin46 =C-IN
pin47 =Ys
pin48 =V-IN
pin49 =DC RE
pin50 =DE-EMP
pin51 =VCC IF/9V
pin52 =DET OUT
pin53 =LOOP FILTER
pin54 =FM DC NF
pin55 =SIF OUT
pin56 =IF GND
TB 1227 DN
pin1 =VID-IN/SCP-OUT
pin2 =VAGC-FILTER
pin3 =H-VCC [5-9v]
pin4 =H-OUT
pin5 =CURVE CORRECTION
pin6 =FBP-IN
pin7 =COINCIDENT-DET
pin8 =VDD [5V]
pin9 =SCL
pin10 =SDA
pin11 =DIGITAL-GND
pin12 =B-OUT
pin13 =G-OUT
pin14 =R-OUT
pin15 =TEXT-GND
pin16 =ABCL
pin17 =RGB-VCC [9V]
pin18 =R-IN/DIGITAL
pin19 =G-IN/DIGITAL
pin20 =B-IN/DIGITAL
pin21 =YS-DIGITAL
pin22 =YS/YM/ANALOG
pin23 =R-IN/ANALOG
pin24 =G-IN/ANALOG
pin25 =B-IN/ANALOG
pin26 =COLOR-LIMITER
pin27 =TV/A-IN
pin28 =EXT-A-IN
pin29 =AUDIO=OUT/VSM-OUT
pin30 =APC-FILT
pin31 =Y-IN
pin32 =FSC-GND
pin33 =B-Y IN
pin34 =R-Y IN
pin35 =R-Y OUT
pin36 =B-Y OUT
pin37 =Y-OUT
pin38 =VDD-FSC [5V]
pin39 =BLACK STRETCH
pin40 =X-TAL/16.2MHZ
pin41 =Y/C-VCC [5V]
pin42 =CHROMA-IN
pin43 =Y/C-GND
pin44 =APL
pin45 =cvbs-in/VID-IN[COMPOSIT]
pin46 =SDEMO-ADJ
pin47 =TV-IN
pin48 =AFC1-FILT
pin49 =SYNC-OUT
pin50 =V-SEP A
pin51 =SYNC-IN
pin52 =V-RAMP
pin53 =V-OUT
pin54 =V-NF
pin55 =DEF-GND
pin56 =VID-OUT/VBLK-OUT
TB 1240 AN
pin1 =AFT OUT
pin2 =A.DE-EM
pin3 =VCC
pin4 =SIF IN
pin5 =IF GND
pin6 =IF IN
pin7 =IF IN
pin8 =RF AGC
pin9 =IF-AGC
pin10 =APC-FILT
pin11 =4.43MHZ
pin12 =Y/C GND
pin13 =YS/YM
pin14 =R IN
pin15 =G IN
pin16 =B IN
pin17 =RGB VCC [5.0]
pin18 =R OUT
pin19 =G OUT
pin20 =B OUT
pin21 =ABL
pin22 =V-RAMP
pin23 =V-NFB
pin24 =V-OUT
pin25 =V-AGC
pin26 =SCL
pin27 =SDA
pin28 =H-VCC [9.1]
pin29 =S-IO/CW-OUT
pin30 =FBP-IN
pin31 =SYNC-OUT
pin32 =H-OUT
pin33 =DEF-GND
pin34 =SCP-OUT
pin35 =E/W-OUT
pin36 =DIG-VCC [9.1]
pin37 =B-Y-IN
pin38 =R-Y-IN
pin39 =Y-IN
pin40 =H-AFC
pin41 =EHT-IN
pin42 =DIG-GND
pin43 =SYNC IN
pin44 =BLK DET
pin45 =C IN
pin46 =Y/C VCC [5.0]
pin47 =IF-DET-OUT
pin48 =LOOP-FILT
pin49 =VCO GND
pin50 =VCO
pin51 =VCO
pin52 =VCO-VCC []
pin53 =SIF
pin54 =RIPPLE
pin55 =SIF/H-PIN
pin56 =FM-DC-NF
TB 1227 AN
pin1 =VID-IN/SCP-OUT
pin2 =VAGC-FILTER
pin3 =H-VCC [5V]
pin4 =H-OUT
pin5 =CURVE CORRECTION
pin6 =FBP-IN
pin7 =COINCIDENT-DET
pin8 =VDD [5V]
pin9 =SCL
pin10 =SDA
pin11 =DIGITAL-GND
pin12 =B-OUT
pin13 =G-OUT
pin14 =R-OUT
pin15 =TEXT-GND
pin16 =ABCL
pin17 =RGB-VCC [9V]
pin18 =R-IN/DIGITAL
pin19 =G-IN/DIGITAL
pin20 =B-IN/DIGITAL
pin21 =YS-DIGITAL
pin22 =YS/YM/ANALOG
pin23 =R-IN/ANALOG
pin24 =G-IN/ANALOG
pin25 =B-IN/ANALOG
pin26 =COLOR-LIMITER
pin27 =TV/A-IN
pin28 =EXT-A-IN
pin29 =AUDIO=OUT/VSM-OUT
pin30 =APC-FILT
pin31 =Y-IN
pin32 =FSC-GND
pin33 =B-Y IN
pin34 =R-Y IN
pin35 =R-Y OUT
pin36 =B-Y OUT
pin37 =Y-OUT
pin38 =VDD-FSC [5V]
pin39 =BLACK STRETCH
pin40 =X-TAL/16MHZ
pin41 =Y/C-VCC [5V]
pin42 =CHROMA-IN
pin43 =Y/C-GND
pin44 =APL
pin45 =VID-IN/COMPOSIT
pin46 =SDEMO-ADJ
pin47 =TV-IN
pin48 =AFC1-FILT
pin49 =SYNC-OUT
pin50 =V-SEP A
pin51 =SYNC-IN
pin52 =V-RAMP
pin53 =V-OUT
pin54 =V-NF
pin55 =DEF-GND
pin56 =VID-OUT/VBLK-OUT
TB1251CN
pin1 =if-vcc
pin2 =ripple filter
pin3 =SIF OUT
pin4 =AUDIO OUT
pin5 =IF-GND
pin6 =IF-IN
pin7 =IF-IN
pin8 =RF-AGC
pin9 =09.1st SIF IN
pin10 =IF-AGC
pin11 =APC-FILTER
pin12 =XTAL [4.43MHZ]
pin13 =CW OUT
pin14 =RGB-VCC [9V]
pin15 =YS/YM SW
pin16 =R.IN [EXT]
pin17 =G IN [EXT]
pin18 =B IN [EXT]
pin19 =Y/C GND
pin20 =R OUT
pin21 =G OUT
pin22 =B OUT
pin23 =V,BIAS FILTER
pin24 =V.RAMP
pin25 =V.NFB
pin26 =V.OUT
pin27 =REF.R
pin28 =ABCL IN
pin29 =H AFC FILTER
pin30 =FBP IN/SCP OUT
pin31 =H.VCC[9V]
pin32 =H.OUT
pin33 =DIG GND
pin34 =SCL
pin35 =SDA
pin36 =BLACK DET
pin37 =DIG VDD
pin38 =SYNC IN
pin39 =Y IN
pin40 =DC RESTOR
pin41 =EW OUT
pin42 =Y/C VCC[5V]
pin43 =C IN
pin44 =Cr IN
pin45 =Cb IN
pin46 =VSM OUT
pin47 =
pin48 =EHT IN
pin49 =DE-EMPHASIS/MON.OUT
pin50 =RF TANK
pin51 =RF TANK
pin52 =DC NF
pin53 =VCO Bias Filter
pin54 =IF DET OUT
pin55 =AFT OUT
pin56 =SIF IN/Hcorr
TB1226DN
pin1 =EXT-VIDEO-IN
pin2 =V-AGC-FILTER
pin3 =H-VCC[9V]
pin4 =H-OUT
pin5 =CURY-CORRING
pin6 =FBP IN
pin7 =COINSIDENCE DET
pin8 =VDD[5V]
pin9 =SCL
pin10 =SDA
pin11 =DIGITAL-GND
pin12 =B OUT
pin13 =G OUT
pin14 =R OUT
pin15 =RGB GND
pin16 =ABCL
pin17 =RGB VCC[9V]
pin18 =R digital
pin19 =G digital
pin20 =B digital
pin21 =Ys/Ym
pin22 =Ys
pin23 =R analog
pin24 =G analog
pin25 =B analog
pin26 =COLOR LIMIT
pin27 =TV AUDIO IN
pin28 =EXT-AUDIO IN
pin29 =AUDIO OUT
pin30 =APC FILT
pin31 =Y2 IN
pin32 =FSC GND
pin33 =B-Y IN
pin34 =R-Y IN
pin35 =R-Y OUT
pin36 =B-Y OUT
pin37 =Y OUT
pin38 =FSC VCC[5V]
pin39 =BLACK FILT
pin40 =XTAL IN [16.2M]
pin41 =Y/C VCC[5V]
pin42 =CHR IN
pin43 =Y/C GND
pin44 =APL
pin45 =Y1 IN
pin46 =S-DEMODULATOR
pin47 =TV VIDEO IN
pin48 =AFC1
pin49 =SYNC OUT
pin50 =VERT SEPARATOR
pin51 =SYNC IN
pin52 =VERT RAMP
pin53 =VERT OUT
pin54 =VERT NF
pin55 =DEF GND
pin56 =VIDEO OUT
LA76931
PIN 1= SIF OUTPUT [2.8V DC]
PIN 2= IF AGC FILTER
PIN 3= SIF INPUT [3.3V DC]
PIN 4= FM FILTER
PIN 5= FM OUTPUT [2.5V~3.5V]
PIN 6= AUDIO OUTPUT [DC]
PIN 7= SND APC FILTER
PIN 8= IF VCC [5V DC]
PIN 9= EXT AUDIO INPUT [2.9V DC]
PIN 10= ABL [AUTO BEAM LIMITER]
PIN 11= RGB VCC [8V DC]
PIN 12=R,G,,B OUTPUT
PIN 13=R,G,,B OUTPUT
PIN 14=R,G,,B OUTPUT
PIN 15= NOT CONNECT
PIN 16= V RAMP OSC.CAPACITOR [Connect 0.47uF capacitor to GND]
PIN 17= VERTICAL OUTPUT
PIN 18= VCO I REFERENCE [Connect 4.7k resister to GND]
PIN 19= HORIZONTAL/BUS VCC [9V DC]
PIN 20= AFC FILTER
PIN 21= HORIZONTAL OUTPUT
PIN 22= VIDEO CHROMA DEFLECTION GND [GND]
PIN 23= NOT CONNECT
PIN 24= NOT CONNECT
PIN 25= SVHS CONTROL [CONTROL S OSD]
PIN 26= REM [Remote control]
PIN 27= AV2[Control av1/av2 input]
PIN 28= AV1[Control av1/av2 input]
PIN 29= NOT CONNECT
PIN 30= MUTE
PIN 31= SDA [I2C control]
PIN 32= SCK [I2C control]
PIN 33= XT1 [32.768KHz]
PIN 34= XT2 [32.768KHz]
PIN 35= CPU VCC [5V DC]
PIN 36= POWER [Control standby]
PIN 37= NOT CONNECT
PIN 38= AGC
PIN 39= KEY [KEY control]
PIN 40= RESET
PIN 41= PLL
PIN 42= CPU GND
PIN 43= CDD VCC [5V DC]
PIN 44= FBP INPUT
PIN 45= C INPUT FOR Y/C MODE
PIN 46= Y INPUT FOR Y/C MODE
PIN 47= DDS FILTER
PIN 48= Y INPUT FOR YcbCr MODE
PIN 49= Cb INPUT forYcbCr MODE
PIN 50= 4.43MHz CRYSTAL
PIN 51= Cr INPUT FOR YcbCr MODE
PIN 52= SELECTED VIDEO OUTPUT OR FSC OUTPUT
PIN 53= CHROMA APC FILTER
PIN 54= EXT VIDEO INPUT
PIN 55= VIDEO CHROMA DEFLECTION VCC
PIN 56= INT VIDEO INPIT
PIN 57= BLACK STRETCH FILTER
PIN 58= PIF APC FILTER
PIN 59= AFT OUTPUT
PIN 60= VIDEO OUTPUT
PIN 61= RF AGC OUTPUT
PIN 62= IF GROUND
PIN 63=PIF AMP INPUT
PIN 64=PIF AMP INPUT
sumber data dari google search
LA76938
PIN1=SIF OUTPUT
PIN2=VIF AGC
PIN3=SIF INPUT
PIN4=FM FILTER
PIN5=FM/AUDIO OUTPUT
PIN6=AUDIO OUTPUT
PIN7=SIF APC FILTER
PIN8=IF VCC[5V]
PIN9=VM
PIN10=ABL
PIN11=RGB VCC[12V]
PIN12=RED OUTPUT
PIN13=GREEN OUTPUT
PIN14=BLUE OUTPUT
PIN15=E/W
PIN16=VERTICAL RAMP OSC
PIN17=VERTICAL OUTPUT
PIN18=VCO IREF
PIN19=HORIZONTAL VCC[12V]
PIN20=HORIZONTAL AFC
PIN21=HORIZONTAL OUTPUT
PIN22=GROUND
PIN23=AV1/AV2
PIN24=TV/AV
PIN25=POWER
PIN26=P.03/INT3[REMOT]
PIN27=VOLUME
PIN28=X-RAY
PIN29=TUNER
PIN30=P.16 PWM.3[MUTE]
PIN31=P.12/SDA1
PIN32=P.13/SCL1
PIN33=X-TAL1
PIN34=X-TAL2
PIN35=VDD[5V]
PIN36=SCART
PIN37=BAND1
PIN38=BAND2
PIN39=KEY
PIN40=RESET
PIN41=PLL
PIN42=CPU GROUND
PIN43=CCD VCC[5V]
PIN44=FBP INPUT
PIN45=BLUE INPUT
PIN46=GREEN INPUT
PIN47=RED INPUT
PIN48=FAST
PIN49=CB
PIN50=X-TAL 4,43MHZ
PIN51=CR
PIN52=V OUTPUT/FSC
PIN53=C APC
PIN54=AV INPUT
PIN55=V/C/D/ VCC[5V]
PIN56=VIDEO INPUT/S-C INPUT[INTERNAL]
PIN57=B L D FILTER
PIN58=APC FILTER
PIN59=AFT FILTER
PIN60=VIDEO OUTPUT
PIN61=RF AGC
PIN62=IF GROUND
PIN63=VIF INPUT 2
PIN64=VIF INPUT1
LA76818A -
LA76810
M52340SP
pal/ntsc single chip color tv signal
pin configuration=
1.aft out
2.limiter in
3.rf agc out
4.if agc filter
5.GND vif
6.vif in1
7.vif in2
8.VCC vif
9.VCC h
10.VCC iil
11.SCL
12.scp out
13.H out
14.H osc
15.SDA
16.afc 1 filter
17.GND interface
18.V pulse out
19.afc 2 filter
20.VCC hi
21.R out
22.G out
23.B out
24.VCC vcd
25.B in
26.contrast
27.G in
28.COincidence
29.R in
30.acident
31.fast blk
32.x-tal 3,58
33.audio by-pass
34.KILL filter
35.CHR apc filter
36.TVin [Yin]
37.GND vcd
38.V[Y] switch out
39.x-tal 4,43
40.sync sep in
41.B-Y out
42.secam ref
43.R-Y out
44.B-Y in
45.R-Y in
46.audio out
47.VCC att
48.FM direct filter
49.vco 1
50.vco 2
51.video apc filter
52.video out
M52707SP
----------------------
M 52707 SP
----------------------
pin1 =KILL FILT
pin2 =ID FILT
pin3 =BUS SW OUT
pin4 =50/60 HZ
pin5 =GND VIF
pin6 =DAC2 REF
pin7 =SYNC SEP
pin8 =SYNC OUT
pin9 =VCC H (8V)
pin10 =VCC IIL
pin11 =SCL
pin12 =SCP
pin13 =H OUT
pin14 =SDA
pin15 =H OSC
pin16 =AFC
pin17 =BYPASS
pin18 =V PULSE OUT
pin19 =AFC FILTER
pin20 =VCC HI (5V)
pin21 =R OUT
pin22 =G OUT
pin23 =B OUT
pin24 =VCC-V/C/D(5V)
pin25 =B IN
pin26 =CONTRASS
pin27 =G IN
pin28 =RGB HOLD
pin29 =R IN
pin30 =BLACK PEAK HOLD
pin31 =FAST BLK
pin32 =XTAL 3,58M
pin33 =CONT REF BYPASS
pin34 =EXT IN (C IN)
pin35 =CHROMA APC FILT
pin36 =TV IN
pin37 =GND V/C/D
pin38 =SW OUT
pin39 =SYNC SEP IN
pin40 =XTAL 4.43M
pin41 =B-Y OUT
pin42 =SECAM REF
pin43 =R-Y OUT
pin44 =B-Y IN
pin45 =R-Y IN
pin46 =AUDIO OUT
pin47 =VCC AUDIO (8V)
pin48 =TV AUDIO IN
pin49 =GND AUDIO
pin50 =EXT AUDIO IN
pin51 =DAC1 OUT
pin52 =DAC1 REF
M52770ASP CHROMA
M52770ASP
01.vif gnd
02.aft out
03.sif limiter in
04.rf agc out
05.qif out
06.if agc filter
07.qif filter
08.spot killer
09.vif in 1
10.vif in 2
11.vif vcc
12.fast blk
13.scl
14.scp out
15.H out
16.vss
17.sda
18.vdd decoupling
19.afc 1 filter
20.H osc
21.mute fltr
22.Rout
23.Gout
24.Bout
25.def.gnd
26.Vout
27.start up
28.B in
29.v ramp fd back
30.v ramp c
31.vcc chroma
32.afc 2 fltr
33.chroma in
34.id fltr
35.video in
36.x-ray in
37.G in
38.blk hot
39.R in
40.contras control
41.x-tal 3.58
42.killer fltr
43.ext in
44.chroma apc fltr
45.TVin
46.gnd video/chroma
47.Y sw out
48.sync sep. in1
49.sync sep. In2
50.x-tal 4.43
51.video clamp
52.secam ref
53.vcc HI
54.B-Y in
55.R-Y in
56.vif apc fltr 2
57.audio out
58.audio bypass
59.ext.audio in
60.fm direct out
61.vif vco 1
62.vif vco 2
63.vif apc fltr 1
64.vif video out
NN5099K
VIDEO PROSESOR BUAT TV
1.test 1
2.scl
3.chroma apc fltr
4.ABCL
5.Ys in
6.ext.R in
7.ext.G in
8.ext.B in
9.vcc1
10.R out
11.G out
12.B out
13.GND/vcj
14.chroma vcxo1/4,43mhz
15.nc
16.vcc1/vif-sif
17.nc
18.vif in1
19.vif in2
20.gnd/vif-sif
21.Qif in
22.rf agc out
23.aft out
24.ext video/chrm in
25.if agc filter
26.vif apc filter
27.Qif det.out
28.sif in
29.ext.audio in
30.audio out
31.det.out/black level
32.de-emphasis filter
33.vcc1/chroma
34.vif det.out
35.vcc3/dac
36.video out
37.test2
38.Yin/Vsinc in
39.horizontal sinc in
40.chroma vcxo2/3,58mhz
41.vcc2/Horizontal vcc
42.Horizontal pulse out
43.Horizontal afc1 fltr
44.audio de-coupling fltr
45.Vertical SAW TOOTH
46.vertical out
47.vertikal agc filter
48.vdd/cmos
49.scp/cw out/xray
50.vss/cmos
51.sda
52.fbp in
OM 8838 PS
OM8838PS
pin01=SIF
pin02=S.EXT
pin03=NC
pin04=NC
pin05=PLL-DE
pin06=V.OUT
pin07=SCL
pin08=SDA
pin09=B-G
pin10=SVHSC
pin11=SVHSY
pin12=VCC
pin13=CVBS-INT
pin14=GND
pin15=AOUT
pin16=CALDEC
pin17=CVBS-EXT
pin18=IBLACK
pin19=BOUT
pin20=GOUT
pin21=ROUT
pin22=IBEAM
pin23=RIN
pin24=GIN
pin25=BIN
pin26=FBL
pin27=YIN
pin28=YOUT
pin29=B-Y OUT
pin30=R-Y OUT
pin31=B-Y IN
pin32=R-Y IN
pin33=SECAM REF
pin34=XTL 3.58M
pin35=XTAL 4.43M
pin36=COLOR PLL
pin37=VCC
pin38=CVBS SW
pin39=BSTRE
pin40=H-OUT
pin41=FB IN/SC OUT
pin42=PH2
pin43=PH1
pin44=GND
pin45=EW DRV
pin46=V DRV B
pin47=V DRV A
pin48=IF
pin49=IF
pin50=EHT (3.9V stop)
pin51=V-SAW
pin52=V-IREF
pin53=AGC
pin54=TUNER AGC
pin55=DE-EM
pin56=SDEC
QXXAVC646
[single prosesor with mikom]
-------------------------
QXXAVC646[single prosesor]
-------------------------
pin1 =SIF OUT
pin2 =VIF AGC
pin3 =SIF IN
pin4 =FM FILTER
pin5 =FM OUT
pin6 =AUDIO OUT
pin7 =SIF APC FILETR
pin8 =VCC-IF[5V]
pin9 =EXT.AUDIO IN
pin10 =ABL
pin11 =VCC-RGB[9V]
pin12 =R OUT
pin13 =G OUT
pin14 =B OUT
pin15 =E/W OUT
pin16 =V RAMP
pin17 =V OUT
pin18 =VCO-IREF
pin19 =H-VCC[9V-24V]
pin20 =H-AFC FILTER
pin21 =H OUT
pin22 =GND-V-VERT
pin23 =P.F
pin24 =S.VIDEO
pin25 =STATUS
pin26 =REMOT IN
pin27 =SDA
pin28 =SCL
pin29 =ON-TIME
pin30 =MUTE
pin31 =IIC-SDA[ke eeprom]
pin32 =IIC-SCL[ke eeprom]
pin33 =xtal[V10B0560N/V10B0570N]
pin34 =xtal[V10B0560N/V10B0570N]
pin35 =VDD[5V]
pin36 =POWER ON/OFF
pin37 =BASS/WOFER
pin38 =VIF-M/BILINGUAL
pin39 =KEY IN
pin40 =RESET
pin41 =FILTER
pin42 =GND-CPU
pin43 =VCC-CCD[5V]
pin44 =FBP IN
pin45 =Yc-C
pin46 =Yc-Y
pin47 =NC
pin48 =DVD-Y
pin49 =Cb IN
pin50 =4.43MHZ
pin51 =Cr IN
pin52 =SVO
pin53 =CHROMA APC FILTER
pin54 =EXT.Y IN
pin55 =VCC-V-VERTICAL[5V]
pin56 =INT.VIDEO
pin57 =BLACK LEVEL[DET FILTER]
pin58 =APC FILTER
pin59 =AFT FILTER
pin60 =VIDEO OUT
pin61 =RF AGC OUT
pin62 =GND-IF
pin63 =PIF IN2
pin64 =PIF IN1
STV223XH CHROMA[mdl:TQFP64]LABA-LABA/TEMPEL termasuk STV2238H
QFP64
1.sl pf 17.if pll.
2.scl 18.gnd if
3.sda 19.am/fm out
4.vcc d 20.vcc if.
5.gnd d 21.in cvbs out
6.audio out 22.ext audio in....
7.fm cap 23.pif lc1
8.sif in1 24.pif lc2
9.sif in2 25.vcc2
10.agc sif cap 26.cvbs in1
11.vref if.... 27.gnd2....
12.agc pif cap.... 28.cvbs in2....
13.pif in1 .... 29.bs....
14.pif in2.... 30.nc....
15.saw ... .31.nc....
16.tuner agc out .... 32.nc
#######################################
33.nc ... .49.r osd....
34.y cvbs in3 .... 50.fb osd....
35.chroma.... 51.nc....
36.apr.... 52.xtal3/btun....
37.b ext/cb.... 53.xtal2....
38.g ext/y .... 54.xtal1....
39.r ext/cr.... 55.cl pf....
40.fb ext .... 56.x1/v amp....
41.ntbc/cvbs out1.... 57.gnd1....
42.nc .... 58.cvbs out2....
43.b out.... 59.vcc1....
44.g out.... 60.nc....
45.rout..... 61.bcl/saf....
46.i cath .... 62.vert....
47.b osd.... 63.h out....
48.g osd.... 64.lfb/ssc..
STV224XH-STV228XH/
termasuk juga STV2286H,STV2248H
SDIP56
PIN OUTPUT DATA=
1.SIF in1
2.SIF in2
3.AGC suf cap
4.V ref if
5.AGC pif cap
6.PIF in1
7.PIF in2
8.TUNER agc out
9.IF pll
10.GND if
11.AM/FM out
12.VCC if
13.in CVBS out
14.ext.AUDIO in
15.PIF lc1
16.PIF lc2
17.VCC2
18.CVBS in1
19.GND2
20.CVBS in2
21.BS
22.Ycvbs in3
23.CHROMA
24.APR
25.B ext/Cb
26.G ext/Y
27.R ext/Cr
28.FB ext
29.ntbc/CVBS out1
30.B out
31.G out
32.R out
33.Icath
34.B osd
35.G osd
36.R osd
37.FB osd/HC
38.xtal3/BTUN
39.xtal2
40.xtal1
41.CLpf
42.x1/v.amp/chroma out
43.GND1
44.CVBS out2
45.vcc1
46.bcl/saf
47.vert
48.h.OUT
49.LFB/SSC
50.SLpf
51.SCL
52.SDA
53.VCCD
54.GND
55.AUDIO out
56.FM cap
CROMA KELUARGA TAxxxx
---------------------------
TA 1201 CN
[ntsc color processor]
---------------------------
pin1 =R audio OUT
pin2 =L audio OUT
pin3 =RF AGC
pin4 =SIF TANK
pin5 =AGC FILTER
pin6 =GND-PIF
pin7 =PIF IN
pin8 =PIF IN
pin9 =VCC-PIF[9V]
pin10 =LOOP FILTER
pin11 =APC FILTER
pin12 =VCXO
pin13 =GND
pin14 =FAST BLANKING
pin15 =R IN
pin16 =G IN
pin17 =B IN
pin18 =VCC-D[3.3V]
pin19 =R OUT
pin20 =G OUT
pin21 =B OUT
pin22 =V OUT
pin23 =V NFB
pin24 =V RAMP
pin25 =V SEP FILTER
pin26 =VCC-H[9V]
pin27 =SCL
pin28 =SDA
pin29 =X-RAY
pin30 =FBP IN
pin31 =SYNC OUT
pin32 =H OUT
pin33 =H AFC
pin34 =32FH VCO
pin35 =GND-D
pin36 =ABL
pin37 =TV IN
pin38 =ACL
pin39 =ext VIDEO
pin40 =BLANK DET
pin41 =AV SW OUT
pin42 =DC REST
pin43 =Y IN
pin44 =AFT
pin45 =CHROMA IN
pin46 =VCC
pin47 =TV DET OUT
pin48 =VCC-SIF[9V]
pin49 =PIF TANK
pin50 =PIF TANK
pin51 =GND-SIF
pin52 =LIMIT IN
pin53 =AUDIO TV IN
pin54 =DE-EMPHASIS
pin55 =L AUDIO IN
pin56 =R AUDIO IN
(cuplikan dari skema tv aiwa)
-------------------------
TA1223AN
-------------------------
pin1 =N.C
pin2 =A-OUT
pin3 =N.C
pin4 =B FIL
pin5 =V FIL
pin6 =A-GND
pin7 =N.C
pin8 =N.C
pin9 =VCC-RGB[9V]
pin10 =R-Y LIMIT
pin11 =APC FIL
pin12 =XTAL
pin13 =GND
pin14 =YS-IN
pin15 =R-IN
pin16 =G-IN
pin17 =B-IN
pin18 =VCC-D[3.3V]
pin19 =R-OUT
pin20 =G-OUT
pin21 =B-OUT
pin22 =V-OUT
pin23 =V-NFB
pin24 =V-RAMP
pin25 =V-SEPA
pin26 =H-VCC[9V]
pin27 =SCL
pin28 =SDA
pin29 =N.C
pin30 =EXT-IN
pin31 =N.C
pin32 =TV A-IN
pin33 =N.C
pin34 =PORT
pin35 =VPL
pin36 =Yr
pin37 =VCC-A[9V]
pin38 =VM
pin39 =VCC-V/C/D[9V]
pin40 =C-IN
pin41 =B.SP
pin42 =Y-IN
pin43 =DC-ADJ
pin44 =VID-OUT
pin45 =PICT
pin46 =V-EXT
pin47 =ACL
pin48 =V-TV
pin49 =ABL
pin50 =GND
pin51 =32fh
pin52 =AFC-FIL
pin53 =H-OUT
pin54 =SYNC-OUT
pin55 =FBP-IN
pin56 =vp-out
[toshiba skema]
---------------------------
TA8690
---------------------------
pin1 =ATT IN (4.2V)
pin2 =SOUND NF IN (4.3V)
pin3 =DE-EMPHASIS (2.1V)
pin4 =SIF DET IN (3.3)
pin5 =SIF LIMITER OUT (4.1)
pin6 =AGC FILTER (5.3)
pin7 =AGC FILTER (5.3)
pin8 =GROUND (PIF/SIF)
pin9 =PIF INM (4.2)
pin10 =PIF IN (4.2)
pin11 =APC FILTER (4.6)
pin12 =FSC VCXO (5.2)
pin13 =VCC-V/C/D (9.0)
pin14 =FSC VCXO (6.6)
pin15 =CLAMP FILTER (3.0)
pin16 =R-Y OUT (5.4)
pin17 =B-Y OUT (5.4)
pin18 =G-Y OUT (5.4)
pin19 =Y OUT (4.8)
pin20 =XRAY PROTECT IN
pin21 =FBP IN (1.1)
pin22 =H OUT (2.2)
pin23 =AFC FILTER (7.3)
pin24 =32 Fh VCO (4.9)
pin25 =VCC H (9.0)
pin26 =R IN OSD (2.0)
pin27 =B IN OSD (2.0)
pin28 =G IN OSD (2.0)
pin29 =V SEPARATOR FILTER (6.0)
pin30 =V PULSE OUT (0.2)
pin31 =VIDEO IN (2.9)
pin32 =TINT (0.0)
pin33 =HI VIDEO IN (8.0)
pin34 =BRIGHTNESS (4.1)
pin35 =CHROMA IN (4.5)
pin36 =SYNC SEPARATOR IN (3.1)
pin37 =GROUND (V/C/D)
pin38 =DC DRIVE (6.2)
pin39 =CONTRASS (5.6)
pin40 =COLOR (4.0)
pin41 =DELAY SIGNAL IN (4.5)
pin42 =KILLER FILTER (5.6)
pin43 =PIF DET OUT (3.4)
pin44 =VCC-PIF/SIF (9.0)
pin45 =PIF TANK (6.6)
pin46 =PIF TANK (6.6)
pin47 =AFT TANK (3.0)
pin48 =AFT OUT (3.2)
pin49 =SIF IN (3.0)
pin50 =ATT CONTROL (0.7)
pin51 =RF AGC OUT (7.2)
pin52 =RF AGC DELAY (1.3)
pin53 =SOUND OUT (4.6)
pin54 =BRIGHT OSD (3.9)
-------------------------
TA8718N
-------------------------
pin1 =VCC
pin2 =DL-IN[50/60]
pin3 =COLOR
pin4 =DL-OUT
pin5 =ACC
pin6 =GND
pin7 =CHROMA-IN
pin8 =KILLER-FILTER
pin9 =APC-FILTER
pin10 =VCO-IN
pin11 =V-OUT
pin12 =VCO-OUT
pin13 =V-RAMP
pin14 =V-NFB
pin15 =H-SHIFT
pin16 =SYNC-IN
pin17 =H-BLK
pin18 =AFC-FILTER
pin19 =32fh VCO
pin20 =H-OUT
pin21 =H-VCC
pin22 =R-OUT
pin23 =G-OUT
pin24 =B-OUT
pin25 =R-CLAMP
pin26 =G-CLAMP
pin27 =B-CLAMP
pin28 =BRIGHT
pin29 =Y-IN
pin30 =CONTRASS
[skema toshiba]
------------------------------
TA8750AN
------------------------------
pin1 =GROUND (0V)
pin2 =DL IN (4.2V)
pin3 =BIAS (4.2V)
pin4 =VCC1 (9V)
pin5 =PAL DL DRIVE (4.2V)
pin6 =DL DRIVE (5.8V)
pin7 =GOUND (0V)
pin8 =UNI COLOR (4.4V)
pin9 =COLOR (4.1V)
pin10 =SECAM IN (7.8V)
pin11 =VCC (9V)
pin12 =SECAM OUT/PAL ID IN (0.2V)
pin13 =ID FILTER (8.7V)
pin14 =ID COIL (3.8V)
pin15 =GATE SWITCH (7.6V)
pin16 =V BLK IN (0V)
pin17 =H BLK IN (1.1V)
pin18 =GATE PULSE FILTER (0.6V)
pin19 =B-Y OUT (5.8V)
pin20 =G-Y OUT (5.5V)
pin21 =R-Y OUT (5.7V)
pin22 =B IN (2V)
pin23 =G IN (2V)
pin24 =R IN (2V)
pin25 =R-Y CLAMP (6.2V)
pin26 =B-Y CLAMP (6.2V)
pin27 =VCC (9V)
pin28 =B-Y DE-EMPHASIS (4.4V)
pin29 =B-Y DE-MODULATOR (3V)
pin30 =B-Y LIMITER OUT (6.7V)
pin31 =PAL B-Y IN (6V)
pin32 =GROUND (0V)
pin33 =PAL R-Y IN (6V)
pin34 =R-Y DE-EMPHASIS (4.1V)
pin35 =R-Y DE-MODULATOR (3V)
pin36 =R-Y LIMITER OUT (6.7V)
-------------------------
TA 8759 BN
(y/c/sync/deflct
signal processor)
-------------------------
pin1 =SR DE-EMP
pin2 =R-Y OUT
pin3 =SR DE-EMP
pin4 =SB DET
pin5 =SB DET
pin6 =VCC[12V]
pin7 =COLOR
pin8 =SR DET
pin9 =SR DET
pin10 =SW1
pin11 =SW2
pin12 =DL IN
pin13 =DC
pin14 =DL OUT
pin15 =TINT
pin16 =ACC FILTER
pin17 =DC feedbeck
pin18 =SECAM IN
pin19 =GND-C
pin20 =P/N IN
pin21 =SW3
pin22 =P IDENT
pin23 =S IDENT
pin24 =S REF
pin25 =APC FILTER
pin26 =3.58MHZ IN
pin27 =N IDENT
pin28 =4.43MHZ IN
pin29 =VERT OUT
pin30 =VCO OUT
pin31 =V RAMP
pin32 =V NF
pin33 =SYNC SEP
pin34 =GP TC
pin35 =H BLK
pin36 =AFC
pin37 =H OSC
pin38 =AFC
pin39 =H OUT
pin40 =VCC-H[9.1V]
pin41 =R
pin42 =G
pin43 =B
pin44 =R clamp
pin45 =G clamp
pin46 =B clamp
pin47 =R TX
pin48 =BRT
pin49 =G TX
pin50 =GND-V/D
pin51 =B TX
pin52 =X-RAY
pin53 =TV/TX SW
pin54 =HALF TONE
pin55 =SHARP
pin56 =PICT IN
pin57 =Y clamp
pin58 =Y IN
pin59 =CONT-CONT
pin60 =R-Y IN
pin61 =VCC[12V]
pin62 =B-Y IN
pin63 =VCC[12V]
pin64 =B-Y OUT
[sumber data dari skema tv AIWA]
-------------------------
TA 8808 BN
-------------------------
pin1 =N.C
pin2 =R-Y OUT[8.2v]
pin3 =N.C
pin4 =N.C
pin5 =N.C
pin6 =VCC-CHROMA[12.3v]
pin7 =COLOR control[3.4v]
pin8 =N.C
pin9 =N.C
pin10 =SW1
pin11 =SW2[5.2v]
pin12 =D/L-IN[5.3v]
pin13 =BIAS[5.3v]
pin14 =D/L-OUT[7.9v]
pin15 =TINT control
pin16 =ACC-FILTER[5.8v]
pin17 =DC-FEEDBACK[3.5v]
pin18 =50/60HZ
pin19 =GND-CHROMA
pin20 =PAL/NTSC-IN[6v]
pin21 =SW3
pin22 =PAL-IDENT[11.7v]
pin23 =N.C
pin24 =N.C
pin25 =APC-FILTER[4.9v]
pin26 =XTAL 3.58MHZ
pin27 =NTSC-IDENT[11.3v]
pin28 =XTAL 4.43MHZ[3.4v]
pin29 =VERT-DRIVE[1.2v]
pin30 =VCXO[8.8v]
pin31 =VERT-RAMP[6v]
pin32 =VERT-NFB[6v]
pin33 =SYNC SEP-IN[6.9v]
pin34 =FILTER GATE PULSE[2.5v]
pin35 =H-BLK-IN[1.3v]
pin36 =AFC-FILTER[7.5v]
pin37 =VCO
pin38 =H-AFC[6.7v]
pin39 =H-OUT[2v]
pin40 =VCC-H[8.9v]
pin41 =R-OUT[4.8v]
pin42 =G-OUT[4.7v]
pin43 =B-OUT[4.6v]
pin44 =R CLAMP[5.1v]
pin45 =G CLAMP[5.1v]
pin46 =B CLAMP[5.1v]
pin47 =EXT.R-IN[7.3v]
pin48 =BRIGHT control[3.8v]
pin49 =EXT.G-IN[7.3v]
pin50 =GND-V/D
pin51 =EXT.B-IN[7.4v]
pin52 =X-RAY[0v]
pin53 =TV-EXT.SW[0v]
pin54 =HALFTONE[0v]
pin55 =PICTURE[6v]
pin56 =DIFF-IN[0v]
pin57 =CLAMP[6v]
pin58 =VIDEO-IN[4.9v]
pin59 =CONTRASS control[3.9v]
pin60 =R-Y IN[6.2v]
pin61 =VCC-VIDEO/DEF[12.3v]
pin62 =B-Y IN[6.2v]
pin63 =VCC-RGB[12.3v]
pin64 =B-Y OUT[8.2v]
[tv goldstar jadul]
---------------------------
TA8879
---------------------------
pin1 =AUDIO OUT
pin2 =RF AGC OUT
pin3 =RF AGC DELAY
pin4 =SIF TANK
pin5 =AGC 1
pin6 =EXT AUDIO IN
pin7 =AGC 2
pin8 =GROUND (PIF/SIF)
pin9 =PIF IN
pin10 =PIF IN
pin11 =Fc ADJUST
pin12 =APC FILTER
pin13 =XTAL (3.58MHZ)
pin14 =VCC-V/C/D (9VOLT)
pin15 =R-Y OUT
pin16 =Y OUT
pin17 =G-Y OUT
pin18 =B-Y OUT
pin19 =R IN OSD
pin20 =G IN OSD
pin21 =FBP IN
pin22 =XRAY
pin23 =H OUT
pin24 =H AFC
pin25 =32Fh VCO
pin26 =VCC-H (9VOLT)
pin27 =V OUT
pin28 =B IN OSD
pin29 =Ys IN OSD
pin30 =V NFB
pin31 =V RAMP
pin32 =KILLER FILTER
pin33 =CHROMA IN
pin34 =VIDEO OUT 2
pin35 =BRIGHT OSD control
pin36 =SHARPNESS control
pin37 =VIDEO IN
pin38 =BRIGHTNESS control
pin39 =V SYNC
pin40 =VIDEO OUT 1
pin41 =GROUND V/C/D
pin42 =EXT VIDEO IN
pin43 =CONTRASS control
pin44 =COLOR control
pin45 =TV INPUT
pin46 =TINT control
pin47 =TV DETECTION OUT
pin48 =VCC-PIF/SIF (9V)
pin49 =PIF TANK
pin50 =PIF TANK
pin51 =AFT TANK
pin52 =AFT OUT
pin53 =SIF IN
pin54 =DE-EMPHASIS
pin55 =AUDIO TV OUT
pin56 =AUDIO control
TDA 3870 PROCESSOR TELEVISION RECEIVER
pin1.video in
pin2.NOISE
pin3.video ou
pin4.IDENT
pin5.video input ext
pin6.COINC
pin7.SW1
pin8.SW2
pin9.SAND
pin10.SCS
pin11.GND/fb
pin12.Vshape/vert.shaper time constant
pin13.Vdrv out
pin14.FBin
pin15.DISCR2
pin16.SAWTO
pin17.Hout
pin18.Hflyback in
pin19.SHIFT
pin20.GND
pin21.OSC/6mhz
pin22.VP[12v]
pin23.START
pin24.DISCR1
pin25.INT
pin26.BIAS/vert.sync.separator
pin27.HSYNC
pin28.MUTE
----- pin01.PW
pin02.ST-BY
pin03.KEY
pin04.GND
pin05.RESET
pin06.XTAL
pin07.XTAL
pin08.TEST
pin09.5V
pin10.GND
pin11.GND
pin12.FBP-IN/SCP-OUT
pin13.H-OUT
pin14.H-AFC
pin15.V-SAW
pin16.V-OUT
pin17.H-VCC
pin18.NC
pin19.Cb
pin20.y-IN
pin21.Cr
pin22.TV-GND
pin23.C-IN
pin24.EXT-IN
pin25.D-VCC/5V
pin26.TV-IN
pin27.ABCL-IN
pin28.AUDIO-OUT
pin29.IF-VCC/9V
pin30.TV-OUT
pin31.SIF-OUT
pin32.EXT-AUDIO
pin33.SIF-IN
pin34.DC-NF
pin35.PIF-PLL
pin36.IF-VCC
pin37.S-REG
pin38.DEEMPH
pin39.IF-AGC
pin40.IF-GND
pin41.IF-IN
pin42.IF-IN
pin43.RF-AGC
pin44.YC-VCC/5V
pin45.MONITOR-OUT
pin46.BLACK-DET
pin47.APC-FIL
pin48.IKIN
pin49.RGB-VCC/9V
pin50.R-OUT
pin51.G-OUT
pin52.B-OUT
pin53.GND
pin54.GND
pin55.5V
pin56.MUTE
pin57.SDA1
pin58.SCL1
pin59.TV/AV
pin60.VOL
pin61.AV-SW
pin62.TV-SYNC
pin63.RMT-IN
pin64.POWER
GOLDSTAR
TMP87PS38N-3K49
01.VSS/GND
02.VT
03.50/60HZ
04.MUTE
05.EXT-MUTE
06.SID
07.POWER
08.U-BAND
09.H-BAND
10.L-BAND
11.SCL.1
12.SDA.1
13.AFC-IN
14.AV.O
15.AV.1
16.KEY.1
17.KEY.2
18.PROT
19.KARA-DAT
20.BUS-ON/OFF
21.VSS/GND
22.R
23.G
24.B
25.Y
26.HD
27.VD
28.OSC.1
29.OSC.2
30.TEST
31.X-IN
32.X-OUT
33.RESET
34.OPTION
35.REMOT
36.H-SYNC
37.SCL.0
38.SDA.0
39.KARA-ON/OFF
40.SYS.0
41.SYS.1
42.VDD/
GOLDSTAR
IX 3031 CE
IX 3031 CE (MICOM/PROGRAM)
pin1 = H SYNC
pin2 =V SYNC
pin3 =ST-BY LED
pin4 =POWER LED
pin5 =AV1/AV2
pin6 =AV/TV
pin7 =SIF MODE AV
pin8 =S VOL
pin9 =KEY IN
pin10 =R/C IN
pin11 =DEF (OP.1)
pin12 =MUTE SOUND OUT
pin13 =SW1 (BILINGUAL)
pin14 =SW2 (B/G)
pin15 =POWER
pin16 =AUDIO SURROUND
pin17 =ON/OFF BILINGUAL(OP.4)
pin18 =CN VSS
pin19 =XTAL IN
pin20 =XTAL OUT
pin21 =VSS
pin22 =VDD (5 VOLT)
pin23 =EXT BUS
pin24 =SETUP
pin25 =RESET
pin26 =...
pin27 =B+ DETECT
pin28 =AFT IN
pin29 =SYNC IN
pin30 =PROTECT IN
pin31 =TUNER (OP.3)
pin32 =SDA
pin33 =OSD (OP.2)
pin34 =SCL
pin35 =AUDIO/VIDEO MUTE
pin36 =DL POWER
pin37 =POWER
pin38 =VIDEO MUTE
pin39 =BLK
pin40 =BLUE
pin41 =GREEN
pin42 =RED
AN5521 VERTICAL DEFLECTION
pin01=.ground
pin02=.output
pin03=.supply output [24volt]
pin04=.input
pin05=.trigger pulse input
pin06=.pulse amp output
pin07=.VCC[24volt]
AN5534CN VERTICAL DRIVER
pin1 =VCC1
pin2 =TRIGGER IN
pin3 =RAMP GENERATOR
pin4 =50/60HZ SW
pin5 =SAW TOOTH WAVE GENERATION
pin6 =FEEDBACK IN
pin7 =VCC2
pin8 =PUMP UP
pin9 =GROUND
pin10=OUTPUT
pin11=output stage VCC
pin12=OSCILLATOR
KA 2131 VERTICAL DRIVER
1 .GND
2 .OUTPUT
3 .nc
4 .AMP VOLTAGE
5 .OSC BLOCKING
6 .V,SAWTOOTH IN/osc signal
7 .BLK PULSE IN
8 .BLK PULSE OUT
9 .VCC[24V max]
10.nc
LA 7837-LA 7838 vertical deflection
1.vcc1[9v]
2.trigger in
3.time constant
4.amplitude control
5.50hz/60hz switch
6.ramp generator
7.ac/dc feedback
8.vcc2[24v]
9.pump-up out
10.osc.stop
11.gnd
12.v.out
13.pwr supply v.out
LA7840 VERTICAL DEFLEKSION
PIN DESCRIPTION
1.ground
2.vert.output
3.output stage
4.non inverting input
5.inverting input
6.vcc[24v]
7.pump-up output
NOTES:
ic ini susunan pinnya sama dengan dengan LA78040 cuma bentuk fisiknya saja yang berbeda
doubel power supply
LA 78040
stv9326 VERTICAL BOOSTER
pin info=
pin01.input inverting
pin02.vcc
pin03.flyback generator
pin04.ground
pin05.output
pin06.output vcc
pin07.input noninverting
STV9379F VERTICAL DEFLECTION
Pin output..............
1.in/inverting...
2.VCC [min10v,max50v]...
3.flyback[max100v]...
4.GND...
6.output stage supply...
7.in/non inverting...
TA8427/8403 VERTICAL
TA8427
1. GND
2. Vertical Output
3. Pump-up Power Supply
4. Input
5. Phase Compensation
6. Power Supply [27V]
7. Pump-up Output
TA8403
1. GND
2. Vertical Output
3. Pump-up Power Supply
4. Input
5. Phase Compensation
6. Power Supply [24V]
7. Pump-up Output
TA 8403 K
TA 8427 K
TA 8445 K
TDA1675A VERTICAL DEFLECTION
TDA8172 VERTICAL BOOST
TDA8174A/8174AW VERTICAL DEFLECTION
TDA 8174 / 8174 W
TDA 8356 VERTICAL
pin1=INPUT A
pin2=INPUT B
pin3=VP+[9-25v]
pin4=V OUTPUT B
pin5=GND/-
pin6=FLYBACK[50v max]
pin7=OUTPUT A
pin8=VO[guard]
pin9=VI feedback in
SUSUNAN PIN SAMA DENGAN
TDA8357 DAN TDA8359
TDA 8359 J VERTICAL FULLBRIDGE
pin1=INPUT A
pin2=INPUT B
pin3=VP[12V]
pin4=OUTPUT B
pin5=GND
pin6=FlyBack VOLTAGE[45v max]
pin7=OUTPUT A
pin8=GUARD OUT/PROTECK
pin9=FEED BACK IN
konfigurasi pinnya sama dengan TDA8356 dan TDA8357
dan bila ada yang mau berexperimen silahkan tidak dilarang
dan resiko ditanggung penumpang
TDA 8357 J
AN 5265 AUDIO
AN5265
pin09.Supply voltage 2
pin08.Sound output
pin07.GND
pin06.Feedback
pin05.Filter
pin04.Volume adjustment
pin03.Mute
pin02.Sound Input
pin01.Supply Voltage 1
AN 5276 AUDIO POWER
VCC = 10 volt – 24 volt ( 19 volt typical)
[1.n.c]...[2.INPUT 1]...
Pin01.n.c
Pin02.input 1
Pin03.ripple filter
Pin04.ground[in]
Pin05.input 2
Pin06.n.c
Pin07.output 2
Pin08.mute
Pin09.ground[out]
Pin10.vcc/max.26v
Pin11.st-by
Pin12.output 1
AN5285K
AN5285K/AUDIO
pin01=.L.IN
pin02=.LVL1.SENSOR
pin03=.L.OUT
pin04=.VCC (13 volt)
pin05=.V.REF
pin06=.GND
pin07=.AGC.ON/OFF
pin08=.R.OUT
pin09=.LVL2.SENSOR
pin10=.R.IN
AN 7124 AUDIO POWER 4 WATT
VCC = 6 volt – 18 volt
AN 7147 N AUDIO POWER 5,3 WATT
VCC = 5 volt – 22 volt
pin01 .NFB ch1
pin02 .INPUT ch1
pin03 .RIPPLE FILT
pin04 .GND in
pin05 .INPUT ch2
pin06 .NFB ch2
pin07 .OUTPUT 2
pin08 .BOOTH STRAP ch2
pin09 .GND out
pin10.VCC
pin11.BOOTH STRAP ch1
pin12.OUTPUT 1
AN7522
AN7522/AUDIO
pin01=.VCC/ (3,5 – 13,5 volt, typikal 8 volt)
pin02=.CH.1out+
pin03=.GND
pin04=.CH.1out-
pin05=.ST-BY
pin06=.CH.1in
pin07=.GND
pin08=.CH.2in
pin09=.VOL
pin10=.CH.2out-
pin11=.GND
pin12=.CH.2out+
LA4220 UNTUK AUDIO
VCC max. 22 volt
output = 3,5 watt
pin01=GND
pin02=OUTPUT
pin03=VCC[16v]
pin04=[13v]
pin05=[12v]
pin06=[9,6v]
pin07=1,8v]
pin08=.....
pin09=........
pin10=input
LA42352
LA42352/SOUND
pin01=FILTER
pin02=INPUT 1
pin03=GROUND
pin04=INPUT 2
pin05=ST-BY
pin06=VOLUME 2
pin07=VCC[20V]
pin08=OUTPUT 2
pin09=NC
pin10=GROUND
pin11=NC
pin12=OUTPUT 1
pin13=VOLUME 1
sumber data skematic tv china chasis_3Y18
untuk lebih detailnya coba cari datasheetnya
LA 42152 audio ampl 15W x 2 ch
LA 4265 AUDIO AMP 3,5 WATT
vcc = 9 – 24 volt ( 16 volt typikal)
pin01=GND
pin02=OUTPUT
pin03=VCC
pin04=nc
pin05=DECOUPLING
pin06=PHASE 1
pin07=PHASE 2
pin08=CLIPPER DIODE
pin09=FEEDBECK
pin10=INPUT
POWER AMPLYFIER LA 4280
VCC = 10 – 40 volt (32 volt typikal)
pin01=phase1
pin02=feed back1
pin03=input1
pin04=Ripple
pin05=GND
pin06=input2
pin07=feed back2
pin08=phase2
pin09=muting
pin10=GND[out]
pin11=output2
pin12=vcc
pin13=output1
pin14=GND[out]
LA 4285-LA4287 AUDIO AMP 7 WATT
pin1.int INPUT
pin2.GND
pin3.ext INPUT
pin4.SWITCH [int/ext]
pin5.EVR control
pin6.DE-COUPLING
pin7.PWR NF
pin8.GND
pin9.OUTPUT
pin10.VCC
ket supply=
LA4285=16V-24V
LA4287=20V-30V
LA4485 STEREO POWER AMP 5WATT
pin01=input 1
pin02=input 2
pin03=.GND
pin04=.BTL in
pin05=.BTL out
pin06=.filter
pin07=.VCC/ls[13.2volt]
pin08=.VCC/ss[13,2volt]
pin09=.st-by
pin10=.mute
pin11=.output 2
pin12=.ground-out
pin13=.output 1
TDA7266S AUDIO
pin01=output1[- ]
pin02=output1[+]
pin03=vcc1
pin04=input1
pin05=nc
pin06=mute
pin07=st-by
pin08=gnd/pwr
pin09=gnd/in
pin10=nc
pin11=nc
pin12=input2
pin13=vcc2
pin14=output2[+]
pin15=output2[- ]
LV 1116 N/NF SURROUND PROSESOR
-------------------
pin01=GND
pin02=Rch A
pin03=Rch B
pin04=Rch C
pin05=Rch LINE OUT
pin06=Rch DC
pin07=ST 1
pin08=LPFC
pin09=Rch TC1
pin10=Rch BC1
pin11=Rch BC2
pin12=Rch OUTPUT
pin13=Rch VR IN
pin14=Rch VR OUT
pin15=L+R
pin16=VREF
pin17=VCC
pin18=VDD
pin19=DATA
pin20=CLOCK
pin21=VSS
pin22=L+R LPF
pin23=Lch VR OUT
pin24=Lch VR IN
pin25=Lch OUTPUT
pin26=Lch BC2
pin27=Lch BC1
pin28=Lch TC1
pin29=HPF C
pin30=ST2
pin31=Lch DC
pin32=Lch LINE OUT
pin33=Lch C
pin34=Lch B
pin35=Lch A
pin36=GND A
TA 8248 k audio power
1.n.c,,2.B.S,,3.out2,,,
PINOUT=
pin01.n.c
pin02.B.S
pin03.out2
pin04.vcc1
pin05.out1
pin06.B.S1
pin07.GND
pin08.vcc2
pin09.ripple
pin10.-inv1
pin11.+inv1
pin12.+inv2
pin13.-inv2
pin14.GND
pin15.GND
AUDIO TDA 1013 B
----------------------------
TDA1013B
----------------------------
pin1 =GND
pin2 =OUTPUT
pin3 =VCC
pin4 =FILTER
pin5 =AMP-IN
pin6 =CONT-OUT
pin7 =VOLUME
pin8 =INPUT
pin9 =GND
TDA1521/TDA1521Q STEREO AMP 12WATT
PIN OUT=
1.in1/non inverting
2.in1/inverting
3.GND
4.OUTPUT 1
5.-Vp symetric[-21v]
6.OUTPUT 2
7.+Vp asymetric[+21v]
8.in2/inverting
9.in2/non inverting
Diposkan oleh MAS TATA
pin1 =SIF IN/SECOND
pin2 =VCC IF/5V
pin3 =SIF IN
pin4 =SIF IN
pin5 =RF AGC
pin6 =IF IN
pin7 =IF IN
pin8 =IF AGC
pin9 =FM FILTER
pin10 =PIF FILTER
pin11 =X-TAL
pin12 =APC FILTER
pin13 =S FILTER
pin14 =VCC YC/5V
pin15 =R OUT
pin16 =G OUT
pin17 =B OUT
pin18 =YC GND
pin19 =VSM OUT
pin20 =Ysm
pin21 =OSD R
pin22 =OSD G
pin23 =OSD B
pin24 =RGB VCC/9V
pin25 =SCL
pin26 =SDA
pin27 =EHT IN
pin28 =ABCL
pin29 =EW OUT
pin30 =CW OUT
pin31 =DIGITAL VDD/9V
pin32 =SCP OUT
pin33 =H-OUT
pin34 =H AFC
pin35 =H-VCC/9V
pin36 =V-RAMP
pin37 =V-OUT
pin38 =DIGITAL GND
pin39 =Cb OUT
pin40 =Cr OUT
pin41 =Y OUT
pin42 =BLACK DET
pin43 =Y IN
pin44 =Cb-IN
pin45 =Cr-IN
pin46 =C-IN
pin47 =Ys
pin48 =V-IN
pin49 =DC RE
pin50 =DE-EMP
pin51 =VCC IF/9V
pin52 =DET OUT
pin53 =LOOP FILTER
pin54 =FM DC NF
pin55 =SIF OUT
pin56 =IF GND
TB 1227 DN
pin1 =VID-IN/SCP-OUT
pin2 =VAGC-FILTER
pin3 =H-VCC [5-9v]
pin4 =H-OUT
pin5 =CURVE CORRECTION
pin6 =FBP-IN
pin7 =COINCIDENT-DET
pin8 =VDD [5V]
pin9 =SCL
pin10 =SDA
pin11 =DIGITAL-GND
pin12 =B-OUT
pin13 =G-OUT
pin14 =R-OUT
pin15 =TEXT-GND
pin16 =ABCL
pin17 =RGB-VCC [9V]
pin18 =R-IN/DIGITAL
pin19 =G-IN/DIGITAL
pin20 =B-IN/DIGITAL
pin21 =YS-DIGITAL
pin22 =YS/YM/ANALOG
pin23 =R-IN/ANALOG
pin24 =G-IN/ANALOG
pin25 =B-IN/ANALOG
pin26 =COLOR-LIMITER
pin27 =TV/A-IN
pin28 =EXT-A-IN
pin29 =AUDIO=OUT/VSM-OUT
pin30 =APC-FILT
pin31 =Y-IN
pin32 =FSC-GND
pin33 =B-Y IN
pin34 =R-Y IN
pin35 =R-Y OUT
pin36 =B-Y OUT
pin37 =Y-OUT
pin38 =VDD-FSC [5V]
pin39 =BLACK STRETCH
pin40 =X-TAL/16.2MHZ
pin41 =Y/C-VCC [5V]
pin42 =CHROMA-IN
pin43 =Y/C-GND
pin44 =APL
pin45 =cvbs-in/VID-IN[COMPOSIT]
pin46 =SDEMO-ADJ
pin47 =TV-IN
pin48 =AFC1-FILT
pin49 =SYNC-OUT
pin50 =V-SEP A
pin51 =SYNC-IN
pin52 =V-RAMP
pin53 =V-OUT
pin54 =V-NF
pin55 =DEF-GND
pin56 =VID-OUT/VBLK-OUT
TB 1240 AN
pin1 =AFT OUT
pin2 =A.DE-EM
pin3 =VCC
pin4 =SIF IN
pin5 =IF GND
pin6 =IF IN
pin7 =IF IN
pin8 =RF AGC
pin9 =IF-AGC
pin10 =APC-FILT
pin11 =4.43MHZ
pin12 =Y/C GND
pin13 =YS/YM
pin14 =R IN
pin15 =G IN
pin16 =B IN
pin17 =RGB VCC [5.0]
pin18 =R OUT
pin19 =G OUT
pin20 =B OUT
pin21 =ABL
pin22 =V-RAMP
pin23 =V-NFB
pin24 =V-OUT
pin25 =V-AGC
pin26 =SCL
pin27 =SDA
pin28 =H-VCC [9.1]
pin29 =S-IO/CW-OUT
pin30 =FBP-IN
pin31 =SYNC-OUT
pin32 =H-OUT
pin33 =DEF-GND
pin34 =SCP-OUT
pin35 =E/W-OUT
pin36 =DIG-VCC [9.1]
pin37 =B-Y-IN
pin38 =R-Y-IN
pin39 =Y-IN
pin40 =H-AFC
pin41 =EHT-IN
pin42 =DIG-GND
pin43 =SYNC IN
pin44 =BLK DET
pin45 =C IN
pin46 =Y/C VCC [5.0]
pin47 =IF-DET-OUT
pin48 =LOOP-FILT
pin49 =VCO GND
pin50 =VCO
pin51 =VCO
pin52 =VCO-VCC []
pin53 =SIF
pin54 =RIPPLE
pin55 =SIF/H-PIN
pin56 =FM-DC-NF
TB 1227 AN
pin1 =VID-IN/SCP-OUT
pin2 =VAGC-FILTER
pin3 =H-VCC [5V]
pin4 =H-OUT
pin5 =CURVE CORRECTION
pin6 =FBP-IN
pin7 =COINCIDENT-DET
pin8 =VDD [5V]
pin9 =SCL
pin10 =SDA
pin11 =DIGITAL-GND
pin12 =B-OUT
pin13 =G-OUT
pin14 =R-OUT
pin15 =TEXT-GND
pin16 =ABCL
pin17 =RGB-VCC [9V]
pin18 =R-IN/DIGITAL
pin19 =G-IN/DIGITAL
pin20 =B-IN/DIGITAL
pin21 =YS-DIGITAL
pin22 =YS/YM/ANALOG
pin23 =R-IN/ANALOG
pin24 =G-IN/ANALOG
pin25 =B-IN/ANALOG
pin26 =COLOR-LIMITER
pin27 =TV/A-IN
pin28 =EXT-A-IN
pin29 =AUDIO=OUT/VSM-OUT
pin30 =APC-FILT
pin31 =Y-IN
pin32 =FSC-GND
pin33 =B-Y IN
pin34 =R-Y IN
pin35 =R-Y OUT
pin36 =B-Y OUT
pin37 =Y-OUT
pin38 =VDD-FSC [5V]
pin39 =BLACK STRETCH
pin40 =X-TAL/16MHZ
pin41 =Y/C-VCC [5V]
pin42 =CHROMA-IN
pin43 =Y/C-GND
pin44 =APL
pin45 =VID-IN/COMPOSIT
pin46 =SDEMO-ADJ
pin47 =TV-IN
pin48 =AFC1-FILT
pin49 =SYNC-OUT
pin50 =V-SEP A
pin51 =SYNC-IN
pin52 =V-RAMP
pin53 =V-OUT
pin54 =V-NF
pin55 =DEF-GND
pin56 =VID-OUT/VBLK-OUT
TB1251CN
pin1 =if-vcc
pin2 =ripple filter
pin3 =SIF OUT
pin4 =AUDIO OUT
pin5 =IF-GND
pin6 =IF-IN
pin7 =IF-IN
pin8 =RF-AGC
pin9 =09.1st SIF IN
pin10 =IF-AGC
pin11 =APC-FILTER
pin12 =XTAL [4.43MHZ]
pin13 =CW OUT
pin14 =RGB-VCC [9V]
pin15 =YS/YM SW
pin16 =R.IN [EXT]
pin17 =G IN [EXT]
pin18 =B IN [EXT]
pin19 =Y/C GND
pin20 =R OUT
pin21 =G OUT
pin22 =B OUT
pin23 =V,BIAS FILTER
pin24 =V.RAMP
pin25 =V.NFB
pin26 =V.OUT
pin27 =REF.R
pin28 =ABCL IN
pin29 =H AFC FILTER
pin30 =FBP IN/SCP OUT
pin31 =H.VCC[9V]
pin32 =H.OUT
pin33 =DIG GND
pin34 =SCL
pin35 =SDA
pin36 =BLACK DET
pin37 =DIG VDD
pin38 =SYNC IN
pin39 =Y IN
pin40 =DC RESTOR
pin41 =EW OUT
pin42 =Y/C VCC[5V]
pin43 =C IN
pin44 =Cr IN
pin45 =Cb IN
pin46 =VSM OUT
pin47 =
pin48 =EHT IN
pin49 =DE-EMPHASIS/MON.OUT
pin50 =RF TANK
pin51 =RF TANK
pin52 =DC NF
pin53 =VCO Bias Filter
pin54 =IF DET OUT
pin55 =AFT OUT
pin56 =SIF IN/Hcorr
TB1226DN
pin1 =EXT-VIDEO-IN
pin2 =V-AGC-FILTER
pin3 =H-VCC[9V]
pin4 =H-OUT
pin5 =CURY-CORRING
pin6 =FBP IN
pin7 =COINSIDENCE DET
pin8 =VDD[5V]
pin9 =SCL
pin10 =SDA
pin11 =DIGITAL-GND
pin12 =B OUT
pin13 =G OUT
pin14 =R OUT
pin15 =RGB GND
pin16 =ABCL
pin17 =RGB VCC[9V]
pin18 =R digital
pin19 =G digital
pin20 =B digital
pin21 =Ys/Ym
pin22 =Ys
pin23 =R analog
pin24 =G analog
pin25 =B analog
pin26 =COLOR LIMIT
pin27 =TV AUDIO IN
pin28 =EXT-AUDIO IN
pin29 =AUDIO OUT
pin30 =APC FILT
pin31 =Y2 IN
pin32 =FSC GND
pin33 =B-Y IN
pin34 =R-Y IN
pin35 =R-Y OUT
pin36 =B-Y OUT
pin37 =Y OUT
pin38 =FSC VCC[5V]
pin39 =BLACK FILT
pin40 =XTAL IN [16.2M]
pin41 =Y/C VCC[5V]
pin42 =CHR IN
pin43 =Y/C GND
pin44 =APL
pin45 =Y1 IN
pin46 =S-DEMODULATOR
pin47 =TV VIDEO IN
pin48 =AFC1
pin49 =SYNC OUT
pin50 =VERT SEPARATOR
pin51 =SYNC IN
pin52 =VERT RAMP
pin53 =VERT OUT
pin54 =VERT NF
pin55 =DEF GND
pin56 =VIDEO OUT
LA76931
PIN 1= SIF OUTPUT [2.8V DC]
PIN 2= IF AGC FILTER
PIN 3= SIF INPUT [3.3V DC]
PIN 4= FM FILTER
PIN 5= FM OUTPUT [2.5V~3.5V]
PIN 6= AUDIO OUTPUT [DC]
PIN 7= SND APC FILTER
PIN 8= IF VCC [5V DC]
PIN 9= EXT AUDIO INPUT [2.9V DC]
PIN 10= ABL [AUTO BEAM LIMITER]
PIN 11= RGB VCC [8V DC]
PIN 12=R,G,,B OUTPUT
PIN 13=R,G,,B OUTPUT
PIN 14=R,G,,B OUTPUT
PIN 15= NOT CONNECT
PIN 16= V RAMP OSC.CAPACITOR [Connect 0.47uF capacitor to GND]
PIN 17= VERTICAL OUTPUT
PIN 18= VCO I REFERENCE [Connect 4.7k resister to GND]
PIN 19= HORIZONTAL/BUS VCC [9V DC]
PIN 20= AFC FILTER
PIN 21= HORIZONTAL OUTPUT
PIN 22= VIDEO CHROMA DEFLECTION GND [GND]
PIN 23= NOT CONNECT
PIN 24= NOT CONNECT
PIN 25= SVHS CONTROL [CONTROL S OSD]
PIN 26= REM [Remote control]
PIN 27= AV2[Control av1/av2 input]
PIN 28= AV1[Control av1/av2 input]
PIN 29= NOT CONNECT
PIN 30= MUTE
PIN 31= SDA [I2C control]
PIN 32= SCK [I2C control]
PIN 33= XT1 [32.768KHz]
PIN 34= XT2 [32.768KHz]
PIN 35= CPU VCC [5V DC]
PIN 36= POWER [Control standby]
PIN 37= NOT CONNECT
PIN 38= AGC
PIN 39= KEY [KEY control]
PIN 40= RESET
PIN 41= PLL
PIN 42= CPU GND
PIN 43= CDD VCC [5V DC]
PIN 44= FBP INPUT
PIN 45= C INPUT FOR Y/C MODE
PIN 46= Y INPUT FOR Y/C MODE
PIN 47= DDS FILTER
PIN 48= Y INPUT FOR YcbCr MODE
PIN 49= Cb INPUT forYcbCr MODE
PIN 50= 4.43MHz CRYSTAL
PIN 51= Cr INPUT FOR YcbCr MODE
PIN 52= SELECTED VIDEO OUTPUT OR FSC OUTPUT
PIN 53= CHROMA APC FILTER
PIN 54= EXT VIDEO INPUT
PIN 55= VIDEO CHROMA DEFLECTION VCC
PIN 56= INT VIDEO INPIT
PIN 57= BLACK STRETCH FILTER
PIN 58= PIF APC FILTER
PIN 59= AFT OUTPUT
PIN 60= VIDEO OUTPUT
PIN 61= RF AGC OUTPUT
PIN 62= IF GROUND
PIN 63=PIF AMP INPUT
PIN 64=PIF AMP INPUT
sumber data dari google search
LA76938
PIN1=SIF OUTPUT
PIN2=VIF AGC
PIN3=SIF INPUT
PIN4=FM FILTER
PIN5=FM/AUDIO OUTPUT
PIN6=AUDIO OUTPUT
PIN7=SIF APC FILTER
PIN8=IF VCC[5V]
PIN9=VM
PIN10=ABL
PIN11=RGB VCC[12V]
PIN12=RED OUTPUT
PIN13=GREEN OUTPUT
PIN14=BLUE OUTPUT
PIN15=E/W
PIN16=VERTICAL RAMP OSC
PIN17=VERTICAL OUTPUT
PIN18=VCO IREF
PIN19=HORIZONTAL VCC[12V]
PIN20=HORIZONTAL AFC
PIN21=HORIZONTAL OUTPUT
PIN22=GROUND
PIN23=AV1/AV2
PIN24=TV/AV
PIN25=POWER
PIN26=P.03/INT3[REMOT]
PIN27=VOLUME
PIN28=X-RAY
PIN29=TUNER
PIN30=P.16 PWM.3[MUTE]
PIN31=P.12/SDA1
PIN32=P.13/SCL1
PIN33=X-TAL1
PIN34=X-TAL2
PIN35=VDD[5V]
PIN36=SCART
PIN37=BAND1
PIN38=BAND2
PIN39=KEY
PIN40=RESET
PIN41=PLL
PIN42=CPU GROUND
PIN43=CCD VCC[5V]
PIN44=FBP INPUT
PIN45=BLUE INPUT
PIN46=GREEN INPUT
PIN47=RED INPUT
PIN48=FAST
PIN49=CB
PIN50=X-TAL 4,43MHZ
PIN51=CR
PIN52=V OUTPUT/FSC
PIN53=C APC
PIN54=AV INPUT
PIN55=V/C/D/ VCC[5V]
PIN56=VIDEO INPUT/S-C INPUT[INTERNAL]
PIN57=B L D FILTER
PIN58=APC FILTER
PIN59=AFT FILTER
PIN60=VIDEO OUTPUT
PIN61=RF AGC
PIN62=IF GROUND
PIN63=VIF INPUT 2
PIN64=VIF INPUT1
LA76818A -
LA76810
M52340SP
pal/ntsc single chip color tv signal
pin configuration=
1.aft out
2.limiter in
3.rf agc out
4.if agc filter
5.GND vif
6.vif in1
7.vif in2
8.VCC vif
9.VCC h
10.VCC iil
11.SCL
12.scp out
13.H out
14.H osc
15.SDA
16.afc 1 filter
17.GND interface
18.V pulse out
19.afc 2 filter
20.VCC hi
21.R out
22.G out
23.B out
24.VCC vcd
25.B in
26.contrast
27.G in
28.COincidence
29.R in
30.acident
31.fast blk
32.x-tal 3,58
33.audio by-pass
34.KILL filter
35.CHR apc filter
36.TVin [Yin]
37.GND vcd
38.V[Y] switch out
39.x-tal 4,43
40.sync sep in
41.B-Y out
42.secam ref
43.R-Y out
44.B-Y in
45.R-Y in
46.audio out
47.VCC att
48.FM direct filter
49.vco 1
50.vco 2
51.video apc filter
52.video out
M52707SP
----------------------
M 52707 SP
----------------------
pin1 =KILL FILT
pin2 =ID FILT
pin3 =BUS SW OUT
pin4 =50/60 HZ
pin5 =GND VIF
pin6 =DAC2 REF
pin7 =SYNC SEP
pin8 =SYNC OUT
pin9 =VCC H (8V)
pin10 =VCC IIL
pin11 =SCL
pin12 =SCP
pin13 =H OUT
pin14 =SDA
pin15 =H OSC
pin16 =AFC
pin17 =BYPASS
pin18 =V PULSE OUT
pin19 =AFC FILTER
pin20 =VCC HI (5V)
pin21 =R OUT
pin22 =G OUT
pin23 =B OUT
pin24 =VCC-V/C/D(5V)
pin25 =B IN
pin26 =CONTRASS
pin27 =G IN
pin28 =RGB HOLD
pin29 =R IN
pin30 =BLACK PEAK HOLD
pin31 =FAST BLK
pin32 =XTAL 3,58M
pin33 =CONT REF BYPASS
pin34 =EXT IN (C IN)
pin35 =CHROMA APC FILT
pin36 =TV IN
pin37 =GND V/C/D
pin38 =SW OUT
pin39 =SYNC SEP IN
pin40 =XTAL 4.43M
pin41 =B-Y OUT
pin42 =SECAM REF
pin43 =R-Y OUT
pin44 =B-Y IN
pin45 =R-Y IN
pin46 =AUDIO OUT
pin47 =VCC AUDIO (8V)
pin48 =TV AUDIO IN
pin49 =GND AUDIO
pin50 =EXT AUDIO IN
pin51 =DAC1 OUT
pin52 =DAC1 REF
M52770ASP CHROMA
M52770ASP
01.vif gnd
02.aft out
03.sif limiter in
04.rf agc out
05.qif out
06.if agc filter
07.qif filter
08.spot killer
09.vif in 1
10.vif in 2
11.vif vcc
12.fast blk
13.scl
14.scp out
15.H out
16.vss
17.sda
18.vdd decoupling
19.afc 1 filter
20.H osc
21.mute fltr
22.Rout
23.Gout
24.Bout
25.def.gnd
26.Vout
27.start up
28.B in
29.v ramp fd back
30.v ramp c
31.vcc chroma
32.afc 2 fltr
33.chroma in
34.id fltr
35.video in
36.x-ray in
37.G in
38.blk hot
39.R in
40.contras control
41.x-tal 3.58
42.killer fltr
43.ext in
44.chroma apc fltr
45.TVin
46.gnd video/chroma
47.Y sw out
48.sync sep. in1
49.sync sep. In2
50.x-tal 4.43
51.video clamp
52.secam ref
53.vcc HI
54.B-Y in
55.R-Y in
56.vif apc fltr 2
57.audio out
58.audio bypass
59.ext.audio in
60.fm direct out
61.vif vco 1
62.vif vco 2
63.vif apc fltr 1
64.vif video out
NN5099K
VIDEO PROSESOR BUAT TV
1.test 1
2.scl
3.chroma apc fltr
4.ABCL
5.Ys in
6.ext.R in
7.ext.G in
8.ext.B in
9.vcc1
10.R out
11.G out
12.B out
13.GND/vcj
14.chroma vcxo1/4,43mhz
15.nc
16.vcc1/vif-sif
17.nc
18.vif in1
19.vif in2
20.gnd/vif-sif
21.Qif in
22.rf agc out
23.aft out
24.ext video/chrm in
25.if agc filter
26.vif apc filter
27.Qif det.out
28.sif in
29.ext.audio in
30.audio out
31.det.out/black level
32.de-emphasis filter
33.vcc1/chroma
34.vif det.out
35.vcc3/dac
36.video out
37.test2
38.Yin/Vsinc in
39.horizontal sinc in
40.chroma vcxo2/3,58mhz
41.vcc2/Horizontal vcc
42.Horizontal pulse out
43.Horizontal afc1 fltr
44.audio de-coupling fltr
45.Vertical SAW TOOTH
46.vertical out
47.vertikal agc filter
48.vdd/cmos
49.scp/cw out/xray
50.vss/cmos
51.sda
52.fbp in
OM 8838 PS
OM8838PS
pin01=SIF
pin02=S.EXT
pin03=NC
pin04=NC
pin05=PLL-DE
pin06=V.OUT
pin07=SCL
pin08=SDA
pin09=B-G
pin10=SVHSC
pin11=SVHSY
pin12=VCC
pin13=CVBS-INT
pin14=GND
pin15=AOUT
pin16=CALDEC
pin17=CVBS-EXT
pin18=IBLACK
pin19=BOUT
pin20=GOUT
pin21=ROUT
pin22=IBEAM
pin23=RIN
pin24=GIN
pin25=BIN
pin26=FBL
pin27=YIN
pin28=YOUT
pin29=B-Y OUT
pin30=R-Y OUT
pin31=B-Y IN
pin32=R-Y IN
pin33=SECAM REF
pin34=XTL 3.58M
pin35=XTAL 4.43M
pin36=COLOR PLL
pin37=VCC
pin38=CVBS SW
pin39=BSTRE
pin40=H-OUT
pin41=FB IN/SC OUT
pin42=PH2
pin43=PH1
pin44=GND
pin45=EW DRV
pin46=V DRV B
pin47=V DRV A
pin48=IF
pin49=IF
pin50=EHT (3.9V stop)
pin51=V-SAW
pin52=V-IREF
pin53=AGC
pin54=TUNER AGC
pin55=DE-EM
pin56=SDEC
QXXAVC646
[single prosesor with mikom]
-------------------------
QXXAVC646[single prosesor]
-------------------------
pin1 =SIF OUT
pin2 =VIF AGC
pin3 =SIF IN
pin4 =FM FILTER
pin5 =FM OUT
pin6 =AUDIO OUT
pin7 =SIF APC FILETR
pin8 =VCC-IF[5V]
pin9 =EXT.AUDIO IN
pin10 =ABL
pin11 =VCC-RGB[9V]
pin12 =R OUT
pin13 =G OUT
pin14 =B OUT
pin15 =E/W OUT
pin16 =V RAMP
pin17 =V OUT
pin18 =VCO-IREF
pin19 =H-VCC[9V-24V]
pin20 =H-AFC FILTER
pin21 =H OUT
pin22 =GND-V-VERT
pin23 =P.F
pin24 =S.VIDEO
pin25 =STATUS
pin26 =REMOT IN
pin27 =SDA
pin28 =SCL
pin29 =ON-TIME
pin30 =MUTE
pin31 =IIC-SDA[ke eeprom]
pin32 =IIC-SCL[ke eeprom]
pin33 =xtal[V10B0560N/V10B0570N]
pin34 =xtal[V10B0560N/V10B0570N]
pin35 =VDD[5V]
pin36 =POWER ON/OFF
pin37 =BASS/WOFER
pin38 =VIF-M/BILINGUAL
pin39 =KEY IN
pin40 =RESET
pin41 =FILTER
pin42 =GND-CPU
pin43 =VCC-CCD[5V]
pin44 =FBP IN
pin45 =Yc-C
pin46 =Yc-Y
pin47 =NC
pin48 =DVD-Y
pin49 =Cb IN
pin50 =4.43MHZ
pin51 =Cr IN
pin52 =SVO
pin53 =CHROMA APC FILTER
pin54 =EXT.Y IN
pin55 =VCC-V-VERTICAL[5V]
pin56 =INT.VIDEO
pin57 =BLACK LEVEL[DET FILTER]
pin58 =APC FILTER
pin59 =AFT FILTER
pin60 =VIDEO OUT
pin61 =RF AGC OUT
pin62 =GND-IF
pin63 =PIF IN2
pin64 =PIF IN1
STV223XH CHROMA[mdl:TQFP64]LABA-LABA/TEMPEL termasuk STV2238H
QFP64
1.sl pf 17.if pll.
2.scl 18.gnd if
3.sda 19.am/fm out
4.vcc d 20.vcc if.
5.gnd d 21.in cvbs out
6.audio out 22.ext audio in....
7.fm cap 23.pif lc1
8.sif in1 24.pif lc2
9.sif in2 25.vcc2
10.agc sif cap 26.cvbs in1
11.vref if.... 27.gnd2....
12.agc pif cap.... 28.cvbs in2....
13.pif in1 .... 29.bs....
14.pif in2.... 30.nc....
15.saw ... .31.nc....
16.tuner agc out .... 32.nc
#######################################
33.nc ... .49.r osd....
34.y cvbs in3 .... 50.fb osd....
35.chroma.... 51.nc....
36.apr.... 52.xtal3/btun....
37.b ext/cb.... 53.xtal2....
38.g ext/y .... 54.xtal1....
39.r ext/cr.... 55.cl pf....
40.fb ext .... 56.x1/v amp....
41.ntbc/cvbs out1.... 57.gnd1....
42.nc .... 58.cvbs out2....
43.b out.... 59.vcc1....
44.g out.... 60.nc....
45.rout..... 61.bcl/saf....
46.i cath .... 62.vert....
47.b osd.... 63.h out....
48.g osd.... 64.lfb/ssc..
STV224XH-STV228XH/
termasuk juga STV2286H,STV2248H
SDIP56
PIN OUTPUT DATA=
1.SIF in1
2.SIF in2
3.AGC suf cap
4.V ref if
5.AGC pif cap
6.PIF in1
7.PIF in2
8.TUNER agc out
9.IF pll
10.GND if
11.AM/FM out
12.VCC if
13.in CVBS out
14.ext.AUDIO in
15.PIF lc1
16.PIF lc2
17.VCC2
18.CVBS in1
19.GND2
20.CVBS in2
21.BS
22.Ycvbs in3
23.CHROMA
24.APR
25.B ext/Cb
26.G ext/Y
27.R ext/Cr
28.FB ext
29.ntbc/CVBS out1
30.B out
31.G out
32.R out
33.Icath
34.B osd
35.G osd
36.R osd
37.FB osd/HC
38.xtal3/BTUN
39.xtal2
40.xtal1
41.CLpf
42.x1/v.amp/chroma out
43.GND1
44.CVBS out2
45.vcc1
46.bcl/saf
47.vert
48.h.OUT
49.LFB/SSC
50.SLpf
51.SCL
52.SDA
53.VCCD
54.GND
55.AUDIO out
56.FM cap
CROMA KELUARGA TAxxxx
---------------------------
TA 1201 CN
[ntsc color processor]
---------------------------
pin1 =R audio OUT
pin2 =L audio OUT
pin3 =RF AGC
pin4 =SIF TANK
pin5 =AGC FILTER
pin6 =GND-PIF
pin7 =PIF IN
pin8 =PIF IN
pin9 =VCC-PIF[9V]
pin10 =LOOP FILTER
pin11 =APC FILTER
pin12 =VCXO
pin13 =GND
pin14 =FAST BLANKING
pin15 =R IN
pin16 =G IN
pin17 =B IN
pin18 =VCC-D[3.3V]
pin19 =R OUT
pin20 =G OUT
pin21 =B OUT
pin22 =V OUT
pin23 =V NFB
pin24 =V RAMP
pin25 =V SEP FILTER
pin26 =VCC-H[9V]
pin27 =SCL
pin28 =SDA
pin29 =X-RAY
pin30 =FBP IN
pin31 =SYNC OUT
pin32 =H OUT
pin33 =H AFC
pin34 =32FH VCO
pin35 =GND-D
pin36 =ABL
pin37 =TV IN
pin38 =ACL
pin39 =ext VIDEO
pin40 =BLANK DET
pin41 =AV SW OUT
pin42 =DC REST
pin43 =Y IN
pin44 =AFT
pin45 =CHROMA IN
pin46 =VCC
pin47 =TV DET OUT
pin48 =VCC-SIF[9V]
pin49 =PIF TANK
pin50 =PIF TANK
pin51 =GND-SIF
pin52 =LIMIT IN
pin53 =AUDIO TV IN
pin54 =DE-EMPHASIS
pin55 =L AUDIO IN
pin56 =R AUDIO IN
(cuplikan dari skema tv aiwa)
-------------------------
TA1223AN
-------------------------
pin1 =N.C
pin2 =A-OUT
pin3 =N.C
pin4 =B FIL
pin5 =V FIL
pin6 =A-GND
pin7 =N.C
pin8 =N.C
pin9 =VCC-RGB[9V]
pin10 =R-Y LIMIT
pin11 =APC FIL
pin12 =XTAL
pin13 =GND
pin14 =YS-IN
pin15 =R-IN
pin16 =G-IN
pin17 =B-IN
pin18 =VCC-D[3.3V]
pin19 =R-OUT
pin20 =G-OUT
pin21 =B-OUT
pin22 =V-OUT
pin23 =V-NFB
pin24 =V-RAMP
pin25 =V-SEPA
pin26 =H-VCC[9V]
pin27 =SCL
pin28 =SDA
pin29 =N.C
pin30 =EXT-IN
pin31 =N.C
pin32 =TV A-IN
pin33 =N.C
pin34 =PORT
pin35 =VPL
pin36 =Yr
pin37 =VCC-A[9V]
pin38 =VM
pin39 =VCC-V/C/D[9V]
pin40 =C-IN
pin41 =B.SP
pin42 =Y-IN
pin43 =DC-ADJ
pin44 =VID-OUT
pin45 =PICT
pin46 =V-EXT
pin47 =ACL
pin48 =V-TV
pin49 =ABL
pin50 =GND
pin51 =32fh
pin52 =AFC-FIL
pin53 =H-OUT
pin54 =SYNC-OUT
pin55 =FBP-IN
pin56 =vp-out
[toshiba skema]
---------------------------
TA8690
---------------------------
pin1 =ATT IN (4.2V)
pin2 =SOUND NF IN (4.3V)
pin3 =DE-EMPHASIS (2.1V)
pin4 =SIF DET IN (3.3)
pin5 =SIF LIMITER OUT (4.1)
pin6 =AGC FILTER (5.3)
pin7 =AGC FILTER (5.3)
pin8 =GROUND (PIF/SIF)
pin9 =PIF INM (4.2)
pin10 =PIF IN (4.2)
pin11 =APC FILTER (4.6)
pin12 =FSC VCXO (5.2)
pin13 =VCC-V/C/D (9.0)
pin14 =FSC VCXO (6.6)
pin15 =CLAMP FILTER (3.0)
pin16 =R-Y OUT (5.4)
pin17 =B-Y OUT (5.4)
pin18 =G-Y OUT (5.4)
pin19 =Y OUT (4.8)
pin20 =XRAY PROTECT IN
pin21 =FBP IN (1.1)
pin22 =H OUT (2.2)
pin23 =AFC FILTER (7.3)
pin24 =32 Fh VCO (4.9)
pin25 =VCC H (9.0)
pin26 =R IN OSD (2.0)
pin27 =B IN OSD (2.0)
pin28 =G IN OSD (2.0)
pin29 =V SEPARATOR FILTER (6.0)
pin30 =V PULSE OUT (0.2)
pin31 =VIDEO IN (2.9)
pin32 =TINT (0.0)
pin33 =HI VIDEO IN (8.0)
pin34 =BRIGHTNESS (4.1)
pin35 =CHROMA IN (4.5)
pin36 =SYNC SEPARATOR IN (3.1)
pin37 =GROUND (V/C/D)
pin38 =DC DRIVE (6.2)
pin39 =CONTRASS (5.6)
pin40 =COLOR (4.0)
pin41 =DELAY SIGNAL IN (4.5)
pin42 =KILLER FILTER (5.6)
pin43 =PIF DET OUT (3.4)
pin44 =VCC-PIF/SIF (9.0)
pin45 =PIF TANK (6.6)
pin46 =PIF TANK (6.6)
pin47 =AFT TANK (3.0)
pin48 =AFT OUT (3.2)
pin49 =SIF IN (3.0)
pin50 =ATT CONTROL (0.7)
pin51 =RF AGC OUT (7.2)
pin52 =RF AGC DELAY (1.3)
pin53 =SOUND OUT (4.6)
pin54 =BRIGHT OSD (3.9)
-------------------------
TA8718N
-------------------------
pin1 =VCC
pin2 =DL-IN[50/60]
pin3 =COLOR
pin4 =DL-OUT
pin5 =ACC
pin6 =GND
pin7 =CHROMA-IN
pin8 =KILLER-FILTER
pin9 =APC-FILTER
pin10 =VCO-IN
pin11 =V-OUT
pin12 =VCO-OUT
pin13 =V-RAMP
pin14 =V-NFB
pin15 =H-SHIFT
pin16 =SYNC-IN
pin17 =H-BLK
pin18 =AFC-FILTER
pin19 =32fh VCO
pin20 =H-OUT
pin21 =H-VCC
pin22 =R-OUT
pin23 =G-OUT
pin24 =B-OUT
pin25 =R-CLAMP
pin26 =G-CLAMP
pin27 =B-CLAMP
pin28 =BRIGHT
pin29 =Y-IN
pin30 =CONTRASS
[skema toshiba]
------------------------------
TA8750AN
------------------------------
pin1 =GROUND (0V)
pin2 =DL IN (4.2V)
pin3 =BIAS (4.2V)
pin4 =VCC1 (9V)
pin5 =PAL DL DRIVE (4.2V)
pin6 =DL DRIVE (5.8V)
pin7 =GOUND (0V)
pin8 =UNI COLOR (4.4V)
pin9 =COLOR (4.1V)
pin10 =SECAM IN (7.8V)
pin11 =VCC (9V)
pin12 =SECAM OUT/PAL ID IN (0.2V)
pin13 =ID FILTER (8.7V)
pin14 =ID COIL (3.8V)
pin15 =GATE SWITCH (7.6V)
pin16 =V BLK IN (0V)
pin17 =H BLK IN (1.1V)
pin18 =GATE PULSE FILTER (0.6V)
pin19 =B-Y OUT (5.8V)
pin20 =G-Y OUT (5.5V)
pin21 =R-Y OUT (5.7V)
pin22 =B IN (2V)
pin23 =G IN (2V)
pin24 =R IN (2V)
pin25 =R-Y CLAMP (6.2V)
pin26 =B-Y CLAMP (6.2V)
pin27 =VCC (9V)
pin28 =B-Y DE-EMPHASIS (4.4V)
pin29 =B-Y DE-MODULATOR (3V)
pin30 =B-Y LIMITER OUT (6.7V)
pin31 =PAL B-Y IN (6V)
pin32 =GROUND (0V)
pin33 =PAL R-Y IN (6V)
pin34 =R-Y DE-EMPHASIS (4.1V)
pin35 =R-Y DE-MODULATOR (3V)
pin36 =R-Y LIMITER OUT (6.7V)
-------------------------
TA 8759 BN
(y/c/sync/deflct
signal processor)
-------------------------
pin1 =SR DE-EMP
pin2 =R-Y OUT
pin3 =SR DE-EMP
pin4 =SB DET
pin5 =SB DET
pin6 =VCC[12V]
pin7 =COLOR
pin8 =SR DET
pin9 =SR DET
pin10 =SW1
pin11 =SW2
pin12 =DL IN
pin13 =DC
pin14 =DL OUT
pin15 =TINT
pin16 =ACC FILTER
pin17 =DC feedbeck
pin18 =SECAM IN
pin19 =GND-C
pin20 =P/N IN
pin21 =SW3
pin22 =P IDENT
pin23 =S IDENT
pin24 =S REF
pin25 =APC FILTER
pin26 =3.58MHZ IN
pin27 =N IDENT
pin28 =4.43MHZ IN
pin29 =VERT OUT
pin30 =VCO OUT
pin31 =V RAMP
pin32 =V NF
pin33 =SYNC SEP
pin34 =GP TC
pin35 =H BLK
pin36 =AFC
pin37 =H OSC
pin38 =AFC
pin39 =H OUT
pin40 =VCC-H[9.1V]
pin41 =R
pin42 =G
pin43 =B
pin44 =R clamp
pin45 =G clamp
pin46 =B clamp
pin47 =R TX
pin48 =BRT
pin49 =G TX
pin50 =GND-V/D
pin51 =B TX
pin52 =X-RAY
pin53 =TV/TX SW
pin54 =HALF TONE
pin55 =SHARP
pin56 =PICT IN
pin57 =Y clamp
pin58 =Y IN
pin59 =CONT-CONT
pin60 =R-Y IN
pin61 =VCC[12V]
pin62 =B-Y IN
pin63 =VCC[12V]
pin64 =B-Y OUT
[sumber data dari skema tv AIWA]
-------------------------
TA 8808 BN
-------------------------
pin1 =N.C
pin2 =R-Y OUT[8.2v]
pin3 =N.C
pin4 =N.C
pin5 =N.C
pin6 =VCC-CHROMA[12.3v]
pin7 =COLOR control[3.4v]
pin8 =N.C
pin9 =N.C
pin10 =SW1
pin11 =SW2[5.2v]
pin12 =D/L-IN[5.3v]
pin13 =BIAS[5.3v]
pin14 =D/L-OUT[7.9v]
pin15 =TINT control
pin16 =ACC-FILTER[5.8v]
pin17 =DC-FEEDBACK[3.5v]
pin18 =50/60HZ
pin19 =GND-CHROMA
pin20 =PAL/NTSC-IN[6v]
pin21 =SW3
pin22 =PAL-IDENT[11.7v]
pin23 =N.C
pin24 =N.C
pin25 =APC-FILTER[4.9v]
pin26 =XTAL 3.58MHZ
pin27 =NTSC-IDENT[11.3v]
pin28 =XTAL 4.43MHZ[3.4v]
pin29 =VERT-DRIVE[1.2v]
pin30 =VCXO[8.8v]
pin31 =VERT-RAMP[6v]
pin32 =VERT-NFB[6v]
pin33 =SYNC SEP-IN[6.9v]
pin34 =FILTER GATE PULSE[2.5v]
pin35 =H-BLK-IN[1.3v]
pin36 =AFC-FILTER[7.5v]
pin37 =VCO
pin38 =H-AFC[6.7v]
pin39 =H-OUT[2v]
pin40 =VCC-H[8.9v]
pin41 =R-OUT[4.8v]
pin42 =G-OUT[4.7v]
pin43 =B-OUT[4.6v]
pin44 =R CLAMP[5.1v]
pin45 =G CLAMP[5.1v]
pin46 =B CLAMP[5.1v]
pin47 =EXT.R-IN[7.3v]
pin48 =BRIGHT control[3.8v]
pin49 =EXT.G-IN[7.3v]
pin50 =GND-V/D
pin51 =EXT.B-IN[7.4v]
pin52 =X-RAY[0v]
pin53 =TV-EXT.SW[0v]
pin54 =HALFTONE[0v]
pin55 =PICTURE[6v]
pin56 =DIFF-IN[0v]
pin57 =CLAMP[6v]
pin58 =VIDEO-IN[4.9v]
pin59 =CONTRASS control[3.9v]
pin60 =R-Y IN[6.2v]
pin61 =VCC-VIDEO/DEF[12.3v]
pin62 =B-Y IN[6.2v]
pin63 =VCC-RGB[12.3v]
pin64 =B-Y OUT[8.2v]
[tv goldstar jadul]
---------------------------
TA8879
---------------------------
pin1 =AUDIO OUT
pin2 =RF AGC OUT
pin3 =RF AGC DELAY
pin4 =SIF TANK
pin5 =AGC 1
pin6 =EXT AUDIO IN
pin7 =AGC 2
pin8 =GROUND (PIF/SIF)
pin9 =PIF IN
pin10 =PIF IN
pin11 =Fc ADJUST
pin12 =APC FILTER
pin13 =XTAL (3.58MHZ)
pin14 =VCC-V/C/D (9VOLT)
pin15 =R-Y OUT
pin16 =Y OUT
pin17 =G-Y OUT
pin18 =B-Y OUT
pin19 =R IN OSD
pin20 =G IN OSD
pin21 =FBP IN
pin22 =XRAY
pin23 =H OUT
pin24 =H AFC
pin25 =32Fh VCO
pin26 =VCC-H (9VOLT)
pin27 =V OUT
pin28 =B IN OSD
pin29 =Ys IN OSD
pin30 =V NFB
pin31 =V RAMP
pin32 =KILLER FILTER
pin33 =CHROMA IN
pin34 =VIDEO OUT 2
pin35 =BRIGHT OSD control
pin36 =SHARPNESS control
pin37 =VIDEO IN
pin38 =BRIGHTNESS control
pin39 =V SYNC
pin40 =VIDEO OUT 1
pin41 =GROUND V/C/D
pin42 =EXT VIDEO IN
pin43 =CONTRASS control
pin44 =COLOR control
pin45 =TV INPUT
pin46 =TINT control
pin47 =TV DETECTION OUT
pin48 =VCC-PIF/SIF (9V)
pin49 =PIF TANK
pin50 =PIF TANK
pin51 =AFT TANK
pin52 =AFT OUT
pin53 =SIF IN
pin54 =DE-EMPHASIS
pin55 =AUDIO TV OUT
pin56 =AUDIO control
TDA 3870 PROCESSOR TELEVISION RECEIVER
pin1.video in
pin2.NOISE
pin3.video ou
pin4.IDENT
pin5.video input ext
pin6.COINC
pin7.SW1
pin8.SW2
pin9.SAND
pin10.SCS
pin11.GND/fb
pin12.Vshape/vert.shaper time constant
pin13.Vdrv out
pin14.FBin
pin15.DISCR2
pin16.SAWTO
pin17.Hout
pin18.Hflyback in
pin19.SHIFT
pin20.GND
pin21.OSC/6mhz
pin22.VP[12v]
pin23.START
pin24.DISCR1
pin25.INT
pin26.BIAS/vert.sync.separator
pin27.HSYNC
pin28.MUTE
----- pin01.PW
pin02.ST-BY
pin03.KEY
pin04.GND
pin05.RESET
pin06.XTAL
pin07.XTAL
pin08.TEST
pin09.5V
pin10.GND
pin11.GND
pin12.FBP-IN/SCP-OUT
pin13.H-OUT
pin14.H-AFC
pin15.V-SAW
pin16.V-OUT
pin17.H-VCC
pin18.NC
pin19.Cb
pin20.y-IN
pin21.Cr
pin22.TV-GND
pin23.C-IN
pin24.EXT-IN
pin25.D-VCC/5V
pin26.TV-IN
pin27.ABCL-IN
pin28.AUDIO-OUT
pin29.IF-VCC/9V
pin30.TV-OUT
pin31.SIF-OUT
pin32.EXT-AUDIO
pin33.SIF-IN
pin34.DC-NF
pin35.PIF-PLL
pin36.IF-VCC
pin37.S-REG
pin38.DEEMPH
pin39.IF-AGC
pin40.IF-GND
pin41.IF-IN
pin42.IF-IN
pin43.RF-AGC
pin44.YC-VCC/5V
pin45.MONITOR-OUT
pin46.BLACK-DET
pin47.APC-FIL
pin48.IKIN
pin49.RGB-VCC/9V
pin50.R-OUT
pin51.G-OUT
pin52.B-OUT
pin53.GND
pin54.GND
pin55.5V
pin56.MUTE
pin57.SDA1
pin58.SCL1
pin59.TV/AV
pin60.VOL
pin61.AV-SW
pin62.TV-SYNC
pin63.RMT-IN
pin64.POWER
GOLDSTAR
TMP87PS38N-3K49
01.VSS/GND
02.VT
03.50/60HZ
04.MUTE
05.EXT-MUTE
06.SID
07.POWER
08.U-BAND
09.H-BAND
10.L-BAND
11.SCL.1
12.SDA.1
13.AFC-IN
14.AV.O
15.AV.1
16.KEY.1
17.KEY.2
18.PROT
19.KARA-DAT
20.BUS-ON/OFF
21.VSS/GND
22.R
23.G
24.B
25.Y
26.HD
27.VD
28.OSC.1
29.OSC.2
30.TEST
31.X-IN
32.X-OUT
33.RESET
34.OPTION
35.REMOT
36.H-SYNC
37.SCL.0
38.SDA.0
39.KARA-ON/OFF
40.SYS.0
41.SYS.1
42.VDD/
GOLDSTAR
IX 3031 CE
IX 3031 CE (MICOM/PROGRAM)
pin1 = H SYNC
pin2 =V SYNC
pin3 =ST-BY LED
pin4 =POWER LED
pin5 =AV1/AV2
pin6 =AV/TV
pin7 =SIF MODE AV
pin8 =S VOL
pin9 =KEY IN
pin10 =R/C IN
pin11 =DEF (OP.1)
pin12 =MUTE SOUND OUT
pin13 =SW1 (BILINGUAL)
pin14 =SW2 (B/G)
pin15 =POWER
pin16 =AUDIO SURROUND
pin17 =ON/OFF BILINGUAL(OP.4)
pin18 =CN VSS
pin19 =XTAL IN
pin20 =XTAL OUT
pin21 =VSS
pin22 =VDD (5 VOLT)
pin23 =EXT BUS
pin24 =SETUP
pin25 =RESET
pin26 =...
pin27 =B+ DETECT
pin28 =AFT IN
pin29 =SYNC IN
pin30 =PROTECT IN
pin31 =TUNER (OP.3)
pin32 =SDA
pin33 =OSD (OP.2)
pin34 =SCL
pin35 =AUDIO/VIDEO MUTE
pin36 =DL POWER
pin37 =POWER
pin38 =VIDEO MUTE
pin39 =BLK
pin40 =BLUE
pin41 =GREEN
pin42 =RED
AN5521 VERTICAL DEFLECTION
pin01=.ground
pin02=.output
pin03=.supply output [24volt]
pin04=.input
pin05=.trigger pulse input
pin06=.pulse amp output
pin07=.VCC[24volt]
AN5534CN VERTICAL DRIVER
pin1 =VCC1
pin2 =TRIGGER IN
pin3 =RAMP GENERATOR
pin4 =50/60HZ SW
pin5 =SAW TOOTH WAVE GENERATION
pin6 =FEEDBACK IN
pin7 =VCC2
pin8 =PUMP UP
pin9 =GROUND
pin10=OUTPUT
pin11=output stage VCC
pin12=OSCILLATOR
KA 2131 VERTICAL DRIVER
1 .GND
2 .OUTPUT
3 .nc
4 .AMP VOLTAGE
5 .OSC BLOCKING
6 .V,SAWTOOTH IN/osc signal
7 .BLK PULSE IN
8 .BLK PULSE OUT
9 .VCC[24V max]
10.nc
LA 7837-LA 7838 vertical deflection
1.vcc1[9v]
2.trigger in
3.time constant
4.amplitude control
5.50hz/60hz switch
6.ramp generator
7.ac/dc feedback
8.vcc2[24v]
9.pump-up out
10.osc.stop
11.gnd
12.v.out
13.pwr supply v.out
LA7840 VERTICAL DEFLEKSION
PIN DESCRIPTION
1.ground
2.vert.output
3.output stage
4.non inverting input
5.inverting input
6.vcc[24v]
7.pump-up output
NOTES:
ic ini susunan pinnya sama dengan dengan LA78040 cuma bentuk fisiknya saja yang berbeda
doubel power supply
LA 78040
stv9326 VERTICAL BOOSTER
pin info=
pin01.input inverting
pin02.vcc
pin03.flyback generator
pin04.ground
pin05.output
pin06.output vcc
pin07.input noninverting
STV9379F VERTICAL DEFLECTION
Pin output..............
1.in/inverting...
2.VCC [min10v,max50v]...
3.flyback[max100v]...
4.GND...
6.output stage supply...
7.in/non inverting...
TA8427/8403 VERTICAL
TA8427
1. GND
2. Vertical Output
3. Pump-up Power Supply
4. Input
5. Phase Compensation
6. Power Supply [27V]
7. Pump-up Output
TA8403
1. GND
2. Vertical Output
3. Pump-up Power Supply
4. Input
5. Phase Compensation
6. Power Supply [24V]
7. Pump-up Output
TA 8403 K
TA 8427 K
TA 8445 K
TDA1675A VERTICAL DEFLECTION
TDA8172 VERTICAL BOOST
TDA8174A/8174AW VERTICAL DEFLECTION
TDA 8174 / 8174 W
TDA 8356 VERTICAL
pin1=INPUT A
pin2=INPUT B
pin3=VP+[9-25v]
pin4=V OUTPUT B
pin5=GND/-
pin6=FLYBACK[50v max]
pin7=OUTPUT A
pin8=VO[guard]
pin9=VI feedback in
SUSUNAN PIN SAMA DENGAN
TDA8357 DAN TDA8359
TDA 8359 J VERTICAL FULLBRIDGE
pin1=INPUT A
pin2=INPUT B
pin3=VP[12V]
pin4=OUTPUT B
pin5=GND
pin6=FlyBack VOLTAGE[45v max]
pin7=OUTPUT A
pin8=GUARD OUT/PROTECK
pin9=FEED BACK IN
konfigurasi pinnya sama dengan TDA8356 dan TDA8357
dan bila ada yang mau berexperimen silahkan tidak dilarang
dan resiko ditanggung penumpang
TDA 8357 J
AN 5265 AUDIO
AN5265
pin09.Supply voltage 2
pin08.Sound output
pin07.GND
pin06.Feedback
pin05.Filter
pin04.Volume adjustment
pin03.Mute
pin02.Sound Input
pin01.Supply Voltage 1
AN 5276 AUDIO POWER
VCC = 10 volt – 24 volt ( 19 volt typical)
[1.n.c]...[2.INPUT 1]...
Pin01.n.c
Pin02.input 1
Pin03.ripple filter
Pin04.ground[in]
Pin05.input 2
Pin06.n.c
Pin07.output 2
Pin08.mute
Pin09.ground[out]
Pin10.vcc/max.26v
Pin11.st-by
Pin12.output 1
AN5285K
AN5285K/AUDIO
pin01=.L.IN
pin02=.LVL1.SENSOR
pin03=.L.OUT
pin04=.VCC (13 volt)
pin05=.V.REF
pin06=.GND
pin07=.AGC.ON/OFF
pin08=.R.OUT
pin09=.LVL2.SENSOR
pin10=.R.IN
AN 7124 AUDIO POWER 4 WATT
VCC = 6 volt – 18 volt
AN 7147 N AUDIO POWER 5,3 WATT
VCC = 5 volt – 22 volt
pin01 .NFB ch1
pin02 .INPUT ch1
pin03 .RIPPLE FILT
pin04 .GND in
pin05 .INPUT ch2
pin06 .NFB ch2
pin07 .OUTPUT 2
pin08 .BOOTH STRAP ch2
pin09 .GND out
pin10.VCC
pin11.BOOTH STRAP ch1
pin12.OUTPUT 1
AN7522
AN7522/AUDIO
pin01=.VCC/ (3,5 – 13,5 volt, typikal 8 volt)
pin02=.CH.1out+
pin03=.GND
pin04=.CH.1out-
pin05=.ST-BY
pin06=.CH.1in
pin07=.GND
pin08=.CH.2in
pin09=.VOL
pin10=.CH.2out-
pin11=.GND
pin12=.CH.2out+
LA4220 UNTUK AUDIO
VCC max. 22 volt
output = 3,5 watt
pin01=GND
pin02=OUTPUT
pin03=VCC[16v]
pin04=[13v]
pin05=[12v]
pin06=[9,6v]
pin07=1,8v]
pin08=.....
pin09=........
pin10=input
LA42352
LA42352/SOUND
pin01=FILTER
pin02=INPUT 1
pin03=GROUND
pin04=INPUT 2
pin05=ST-BY
pin06=VOLUME 2
pin07=VCC[20V]
pin08=OUTPUT 2
pin09=NC
pin10=GROUND
pin11=NC
pin12=OUTPUT 1
pin13=VOLUME 1
sumber data skematic tv china chasis_3Y18
untuk lebih detailnya coba cari datasheetnya
LA 42152 audio ampl 15W x 2 ch
LA 4265 AUDIO AMP 3,5 WATT
vcc = 9 – 24 volt ( 16 volt typikal)
pin01=GND
pin02=OUTPUT
pin03=VCC
pin04=nc
pin05=DECOUPLING
pin06=PHASE 1
pin07=PHASE 2
pin08=CLIPPER DIODE
pin09=FEEDBECK
pin10=INPUT
POWER AMPLYFIER LA 4280
VCC = 10 – 40 volt (32 volt typikal)
pin01=phase1
pin02=feed back1
pin03=input1
pin04=Ripple
pin05=GND
pin06=input2
pin07=feed back2
pin08=phase2
pin09=muting
pin10=GND[out]
pin11=output2
pin12=vcc
pin13=output1
pin14=GND[out]
LA 4285-LA4287 AUDIO AMP 7 WATT
pin1.int INPUT
pin2.GND
pin3.ext INPUT
pin4.SWITCH [int/ext]
pin5.EVR control
pin6.DE-COUPLING
pin7.PWR NF
pin8.GND
pin9.OUTPUT
pin10.VCC
ket supply=
LA4285=16V-24V
LA4287=20V-30V
LA4485 STEREO POWER AMP 5WATT
pin01=input 1
pin02=input 2
pin03=.GND
pin04=.BTL in
pin05=.BTL out
pin06=.filter
pin07=.VCC/ls[13.2volt]
pin08=.VCC/ss[13,2volt]
pin09=.st-by
pin10=.mute
pin11=.output 2
pin12=.ground-out
pin13=.output 1
TDA7266S AUDIO
pin01=output1[- ]
pin02=output1[+]
pin03=vcc1
pin04=input1
pin05=nc
pin06=mute
pin07=st-by
pin08=gnd/pwr
pin09=gnd/in
pin10=nc
pin11=nc
pin12=input2
pin13=vcc2
pin14=output2[+]
pin15=output2[- ]
LV 1116 N/NF SURROUND PROSESOR
-------------------
pin01=GND
pin02=Rch A
pin03=Rch B
pin04=Rch C
pin05=Rch LINE OUT
pin06=Rch DC
pin07=ST 1
pin08=LPFC
pin09=Rch TC1
pin10=Rch BC1
pin11=Rch BC2
pin12=Rch OUTPUT
pin13=Rch VR IN
pin14=Rch VR OUT
pin15=L+R
pin16=VREF
pin17=VCC
pin18=VDD
pin19=DATA
pin20=CLOCK
pin21=VSS
pin22=L+R LPF
pin23=Lch VR OUT
pin24=Lch VR IN
pin25=Lch OUTPUT
pin26=Lch BC2
pin27=Lch BC1
pin28=Lch TC1
pin29=HPF C
pin30=ST2
pin31=Lch DC
pin32=Lch LINE OUT
pin33=Lch C
pin34=Lch B
pin35=Lch A
pin36=GND A
TA 8248 k audio power
1.n.c,,2.B.S,,3.out2,,,
PINOUT=
pin01.n.c
pin02.B.S
pin03.out2
pin04.vcc1
pin05.out1
pin06.B.S1
pin07.GND
pin08.vcc2
pin09.ripple
pin10.-inv1
pin11.+inv1
pin12.+inv2
pin13.-inv2
pin14.GND
pin15.GND
AUDIO TDA 1013 B
----------------------------
TDA1013B
----------------------------
pin1 =GND
pin2 =OUTPUT
pin3 =VCC
pin4 =FILTER
pin5 =AMP-IN
pin6 =CONT-OUT
pin7 =VOLUME
pin8 =INPUT
pin9 =GND
TDA1521/TDA1521Q STEREO AMP 12WATT
PIN OUT=
1.in1/non inverting
2.in1/inverting
3.GND
4.OUTPUT 1
5.-Vp symetric[-21v]
6.OUTPUT 2
7.+Vp asymetric[+21v]
8.in2/inverting
9.in2/non inverting
Diposkan oleh MAS TATA
PARAMETER TV CINA
8823 CPANG
RCUT 9D
GCUT 90
BCUT 8F
GDRV 48
BDRV 63+CNTX 65+BRTC 45
COLC 40
TNTC 40
COLP 00
COLS 40+SCOL 07
SCNT 0A+CNTC 58+CNTN 00
HPOS 0D
VP50 03
HIT 16
VLIN 0B
SBY 08
SRY 08
RAGC 28
*MENU D
BRTX 35
BRTN 25
COLX 3F
COLN 00
TNTX 28
TNTN 28
ST3 25
SV 25
ST4 29
SV429
SVD 26
ASSH 07
SHPX 38
SHPN 15
TXCX 10
RGCN 1F
ABL 37
DCBS 23
CLTO 0B
CLTM 4B
CLVO 4B
CLVD 4B
DEF 01
AKB 00
SECD 18
HPOS 0D
VP50 03
HIT 16
HPS 04
VP60 00
HITS 02
VLIN 0B
VSC 06
VLIS 01
VSS 02
SBY 08
SRY 08
BRTS 05
RAGC 28
HAFC 09
V25 50
V50 60
V100 7B
MUTT 00
STST 00
FLG0 52
FLG1 04
REFP 00
RSNS 00
GSNS 00
BSNS 00
MOD 30
STBY 00
SVM 00
VBLK 00
VCEN 2A
HSIZE 20
PRBR 20
TRUM 10
ECCT 10
ECCB 10
EHT 24
UCOM 00
PYNX 2E
PYNN 18
PYXS 22
PYNS 1E
RCUTS 10
GCUTS 00
BCUTS 10
GDRVS 00
BDRVS 00
BDRVS 00
NOIS 01
AV OPT 05
OPT2 38
WAIT TIME 2F
CUR CEN 9D
CUR STEP 03
AUS TP 04
MODE0 9B
MODE1 07
MODE2 E7
OSDV 53
HIT0 0D
EFFECT1 37
EFFECT2 37
CAS 20
CAS1 60
CAS2 63
LOGOP B5
LOGOP1 EA
LOGOP2 1A
LOGOP3 1A
MCOL 05
BASC 40
BASX 72
TREC 3C
BALC 3F
WOPC 38
OSD 0F
OPT C7
8823 CPANG
RCUT 9D
GCUT 90
BCUT 8F
GDRV 48
BDRV 63+CNTX 65+BRTC 45
COLC 40
TNTC 40
COLP 00
COLS 40+SCOL 07
SCNT 0A+CNTC 58+CNTN 00
HPOS 0D
VP50 03
HIT 16
VLIN 0B
SBY 08
SRY 08
RAGC 28
*MENU D
BRTX 35
BRTN 25
COLX 3F
COLN 00
TNTX 28
TNTN 28
ST3 25
SV 25
ST4 29
SV429
SVD 26
ASSH 07
SHPX 38
SHPN 15
TXCX 10
RGCN 1F
ABL 37
DCBS 23
CLTO 0B
CLTM 4B
CLVO 4B
CLVD 4B
DEF 01
AKB 00
SECD 18
HPOS 0D
VP50 03
HIT 16
HPS 04
VP60 00
HITS 02
VLIN 0B
VSC 06
VLIS 01
VSS 02
SBY 08
SRY 08
BRTS 05
RAGC 28
HAFC 09
V25 50
V50 60
V100 7B
MUTT 00
STST 00
FLG0 52
FLG1 04
REFP 00
RSNS 00
GSNS 00
BSNS 00
MOD 30
STBY 00
SVM 00
VBLK 00
VCEN 2A
HSIZE 20
PRBR 20
TRUM 10
ECCT 10
ECCB 10
EHT 24
UCOM 00
PYNX 2E
PYNN 18
PYXS 22
PYNS 1E
RCUTS 10
GCUTS 00
BCUTS 10
GDRVS 00
BDRVS 00
BDRVS 00
NOIS 01
AV OPT 05
OPT2 38
WAIT TIME 2F
CUR CEN 9D
CUR STEP 03
AUS TP 04
MODE0 9B
MODE1 07
MODE2 E7
OSDV 53
HIT0 0D
EFFECT1 37
EFFECT2 37
CAS 20
CAS1 60
CAS2 63
LOGOP B5
LOGOP1 EA
LOGOP2 1A
LOGOP3 1A
MCOL 05
BASC 40
BASX 72
TREC 3C
BALC 3F
WOPC 38
OSD 0F
OPT C7
Parameter tv cina
8873-cpang
F.MENU 0
H.FASE 16
V.VOSITION 3
V.SIZE 16
V.LINE 23
V.SC 11
F.MENU1
OSD H.POSI.44
OSD V.POSI.20
OSD CON.1
OSDF.103
AGC12.32
WTIM.10
CENT.195
STEP.2
F.MENU 2
SUB.BRI 0
SUB.CON 10
SUB.P.COLOR 10
ST3 25
ST4 25
F. 3
OPT F7
OPT2 0D
MOD 01
MOD0 21
MOD1 07
MOD2 04
VCD0 08
LANG 01
NOISE 10
F. 4
CNTX 7F
CNTC 50
CNTN 20
BRTX 35
BRTC 40
BRTN 25
COLX 3F
COLC 30
COLN 00
F. 5
TNTX 28
TNTC 40
TNTN 28
SHPX 14
SHPN 15
ASSH 03
SV3 25
SV4 25
SVD 25
F. 6
FS 38M
HAFC 89
VBLK 00
VCEN 16
PYNX 33
PYNN 11
PYXS 22
PYNS 1E
SVM 10
F. 7
DCBS 13
CLT0 0D
CLTM 4B
CLV0 4B
CLVD 4B
FLG0 02
FLG1 03
HPARA 03
F. 8
V25 40
V50 60
V100 7F
WCTL OF
BASC 24
BASX 72
TREC 40
BALC 40
WOFC 7F
F. 9
SBOX E9
XBOX 89
SHS 10
SHE 7D
SVS 18
SVE FF
SET2 05
UVBLACK 86
BW BALANCE
RC 75
GC 74
BC 75
GD 60
BD 70
SSBG 08
SSI 08
SSDK 08
SSM 08
SYNC 02
SYBB 00
SYSR 02
BBCT 04
NDTC 1F
STBG 08
STI 08
STDK 08
STM 08
VIDIO T/A1/A2/D
SOUND IC OFF
S.WOFFER OFF
CH DARK ON
OPEN CURT.OFF
CLOSE CURT. OFF
SND INPUT AV1.ST
TUNER VT
ABL 15
8873-cpang
F.MENU 0
H.FASE 16
V.VOSITION 3
V.SIZE 16
V.LINE 23
V.SC 11
F.MENU1
OSD H.POSI.44
OSD V.POSI.20
OSD CON.1
OSDF.103
AGC12.32
WTIM.10
CENT.195
STEP.2
F.MENU 2
SUB.BRI 0
SUB.CON 10
SUB.P.COLOR 10
ST3 25
ST4 25
F. 3
OPT F7
OPT2 0D
MOD 01
MOD0 21
MOD1 07
MOD2 04
VCD0 08
LANG 01
NOISE 10
F. 4
CNTX 7F
CNTC 50
CNTN 20
BRTX 35
BRTC 40
BRTN 25
COLX 3F
COLC 30
COLN 00
F. 5
TNTX 28
TNTC 40
TNTN 28
SHPX 14
SHPN 15
ASSH 03
SV3 25
SV4 25
SVD 25
F. 6
FS 38M
HAFC 89
VBLK 00
VCEN 16
PYNX 33
PYNN 11
PYXS 22
PYNS 1E
SVM 10
F. 7
DCBS 13
CLT0 0D
CLTM 4B
CLV0 4B
CLVD 4B
FLG0 02
FLG1 03
HPARA 03
F. 8
V25 40
V50 60
V100 7F
WCTL OF
BASC 24
BASX 72
TREC 40
BALC 40
WOFC 7F
F. 9
SBOX E9
XBOX 89
SHS 10
SHE 7D
SVS 18
SVE FF
SET2 05
UVBLACK 86
BW BALANCE
RC 75
GC 74
BC 75
GD 60
BD 70
SSBG 08
SSI 08
SSDK 08
SSM 08
SYNC 02
SYBB 00
SYSR 02
BBCT 04
NDTC 1F
STBG 08
STI 08
STDK 08
STM 08
VIDIO T/A1/A2/D
SOUND IC OFF
S.WOFFER OFF
CH DARK ON
OPEN CURT.OFF
CLOSE CURT. OFF
SND INPUT AV1.ST
TUNER VT
ABL 15
Senin, 04 April 2011
test flayback
CARA MUDAH
MENGANALISA KERUSAKAN TRAFO
FLAYBACK TV
Artikel sederhana ini saya tulis
untuk rekan2 pemula di bidang
elektronik khususnya perbaikan
pesawat TV BERWARNA.Bagi
rekan2 yang sudah senior tentu
sudah bukan hal yg sulit untuk
menentukan apakah trafo fly back
masih layak atau tidak untuk di
pakai.saya tidak menganjurkan
kepada rekan2 untuk
mengunakan tester flyback
karena hal itu dapat
membingungkan rekan2.hal ini
saya ungkapkan sebab ini adalah
pengalaman pribadi ,pada tahun
1997 saat itu saya baru lulus STM
elektro saya dapat order untuk
mengerjakan pesawat TV punya
teman satu kelas sama2
STM ,hitung 2 cari
pengalaman.merek tv tersebut
DIGITEC NINJA 14",dengan
kerusakan mati total.berbekal
teori dan praktek seadanya kami
mencoba menganalisa kerusakan
tv tersebut.pertama2 kami cek
rangkaian power supply ternyata
tidak ada kerusakan lalu saya
ukur capasitor B+ output power
supply ternyata korslet (0 ohm)ke
ground.setelah saya telusuri
ternyata pin B+ flyback yang
korslet ke pin ground,saya
katakan kepada teman saya ini
flybacknya yg rusak,terus dia
katakan apa kamu sudah yakin
soalnya harga flyback saat itu
dikota makassar termasuk
mahal.setelah berunding akhirnya
kami putuskan untuk melakukan
test flyback karena ada beberapa
toko suku cadang yang menerima
jasa test flyback dgn bayaran
rp5000.setelah dilakukan test
ternyata hasilnya bagus menurut
yg test saya sendiri lihat tegangan
tingginya ada. hal ini mebuat
bingung kok bisa flyback yg
sudah korslet bisa mengeluarkan
teg tinggi.saya berdebat hebat
saat itu dengan teman karena ia
lebih percaya hasil test alat itu lalu
kami putuskan untuk melakukan
hasil test kembali ditoko yg lain
hasilnya sama saja GOOD saya pun
jadi ragu ganti apa tidak
flybacknya.sebab teman sudah
yakin bahwa flybacknya masih
bagus.akhirnya saya putuskan
untuk mengganti flyback tersebut
dgn resiko bahwa apabila
ternyata flyback yg saya ganti
masih bagus maka saya harus
tuntaskan prbaikan tv tersebut
tanpa dibayar.ternyata setelah
penggantian trafo flyback TV
langsung OKE.kenapa hal ini
terjadi ternyata tester flyback
hanya berguna rusak tidaknya
dioda HV RECT didalam flayback
ditandai ada tidaknya tegangan
tinggi yg keluar di anoda.2.besar
kecilnya teg anoda pun tak dapat
diketahui apa sesuai dgn
spesifikasi pesawat TV tersebut
apa tidak seperti diketahui teg
anoda sekitar 20-25kv.rata rata
kerusakan fly back tv jaman
sekarang jarang sekali rusak di
bagian dioda HV RECT.tidak
pernah saya jumpai TV yg heater
crt nyala,teg 180v ada 24v oke dll
tapi tegangan tingginya 0v.hal itu
cuma terjadi pada tv tahun 70an
alias BW..kembali kepokok
persoalan gejala yg ditimbulkan
oleh kerusakan trafo flyback pada
umumnya menyebabkan tv mati
biasanya disertai suara derit atau
ciutan dari trafo SMPS power
supply.2korsletnya Transistor
HORIZONTAL output.teg output B
+power supply drop +_ 50%
diseratai panas yg tidak wajar TR
HORIZONTAL out.3.apabila
mendapati resistor ABL terbakar
maka hampir dapat dipastikan
flyback rusak.4.bocornya
tegangan tinggi di bodi flayback
ciri2nya keluarnya kilatan
tegangan tinggi yg menembak ke
ground dari bodi flyback.5.korslet
spul meyebabkan pin B+,C,180v
terhubung dgn pin
GROUND.6.tegangan supply G2
dan FOKUS tidak bisa diatur akibat
rusaknya VR pengatur screen dan
fokus di flayback. sebagai
penutup mungkin masih banyak
hal 2 yang terjadi akibat tidak
normalnya kinerja flayback tapi
beberapa poin yg saya tulis diatas
adalah hal yg paling sering terjadi
akibat kerusakan flyback, semoga
ada manfaatnya bagi rekan2
AMIN.
MENGANALISA KERUSAKAN TRAFO
FLAYBACK TV
Artikel sederhana ini saya tulis
untuk rekan2 pemula di bidang
elektronik khususnya perbaikan
pesawat TV BERWARNA.Bagi
rekan2 yang sudah senior tentu
sudah bukan hal yg sulit untuk
menentukan apakah trafo fly back
masih layak atau tidak untuk di
pakai.saya tidak menganjurkan
kepada rekan2 untuk
mengunakan tester flyback
karena hal itu dapat
membingungkan rekan2.hal ini
saya ungkapkan sebab ini adalah
pengalaman pribadi ,pada tahun
1997 saat itu saya baru lulus STM
elektro saya dapat order untuk
mengerjakan pesawat TV punya
teman satu kelas sama2
STM ,hitung 2 cari
pengalaman.merek tv tersebut
DIGITEC NINJA 14",dengan
kerusakan mati total.berbekal
teori dan praktek seadanya kami
mencoba menganalisa kerusakan
tv tersebut.pertama2 kami cek
rangkaian power supply ternyata
tidak ada kerusakan lalu saya
ukur capasitor B+ output power
supply ternyata korslet (0 ohm)ke
ground.setelah saya telusuri
ternyata pin B+ flyback yang
korslet ke pin ground,saya
katakan kepada teman saya ini
flybacknya yg rusak,terus dia
katakan apa kamu sudah yakin
soalnya harga flyback saat itu
dikota makassar termasuk
mahal.setelah berunding akhirnya
kami putuskan untuk melakukan
test flyback karena ada beberapa
toko suku cadang yang menerima
jasa test flyback dgn bayaran
rp5000.setelah dilakukan test
ternyata hasilnya bagus menurut
yg test saya sendiri lihat tegangan
tingginya ada. hal ini mebuat
bingung kok bisa flyback yg
sudah korslet bisa mengeluarkan
teg tinggi.saya berdebat hebat
saat itu dengan teman karena ia
lebih percaya hasil test alat itu lalu
kami putuskan untuk melakukan
hasil test kembali ditoko yg lain
hasilnya sama saja GOOD saya pun
jadi ragu ganti apa tidak
flybacknya.sebab teman sudah
yakin bahwa flybacknya masih
bagus.akhirnya saya putuskan
untuk mengganti flyback tersebut
dgn resiko bahwa apabila
ternyata flyback yg saya ganti
masih bagus maka saya harus
tuntaskan prbaikan tv tersebut
tanpa dibayar.ternyata setelah
penggantian trafo flyback TV
langsung OKE.kenapa hal ini
terjadi ternyata tester flyback
hanya berguna rusak tidaknya
dioda HV RECT didalam flayback
ditandai ada tidaknya tegangan
tinggi yg keluar di anoda.2.besar
kecilnya teg anoda pun tak dapat
diketahui apa sesuai dgn
spesifikasi pesawat TV tersebut
apa tidak seperti diketahui teg
anoda sekitar 20-25kv.rata rata
kerusakan fly back tv jaman
sekarang jarang sekali rusak di
bagian dioda HV RECT.tidak
pernah saya jumpai TV yg heater
crt nyala,teg 180v ada 24v oke dll
tapi tegangan tingginya 0v.hal itu
cuma terjadi pada tv tahun 70an
alias BW..kembali kepokok
persoalan gejala yg ditimbulkan
oleh kerusakan trafo flyback pada
umumnya menyebabkan tv mati
biasanya disertai suara derit atau
ciutan dari trafo SMPS power
supply.2korsletnya Transistor
HORIZONTAL output.teg output B
+power supply drop +_ 50%
diseratai panas yg tidak wajar TR
HORIZONTAL out.3.apabila
mendapati resistor ABL terbakar
maka hampir dapat dipastikan
flyback rusak.4.bocornya
tegangan tinggi di bodi flayback
ciri2nya keluarnya kilatan
tegangan tinggi yg menembak ke
ground dari bodi flyback.5.korslet
spul meyebabkan pin B+,C,180v
terhubung dgn pin
GROUND.6.tegangan supply G2
dan FOKUS tidak bisa diatur akibat
rusaknya VR pengatur screen dan
fokus di flayback. sebagai
penutup mungkin masih banyak
hal 2 yang terjadi akibat tidak
normalnya kinerja flayback tapi
beberapa poin yg saya tulis diatas
adalah hal yg paling sering terjadi
akibat kerusakan flyback, semoga
ada manfaatnya bagi rekan2
AMIN.
Tr sanken
Tips menentukan Tr
sanken asli atau
palsu,..."tempelkan k2 tr trsbut
pada maknet dan nyang
menempel erat pda maknet
adalah tr palsu dan yg tdk nempel
adalah yg asli" smoga brmanfaat
untuk pecinta solder senusantara.
sanken asli atau
palsu,..."tempelkan k2 tr trsbut
pada maknet dan nyang
menempel erat pda maknet
adalah tr palsu dan yg tdk nempel
adalah yg asli" smoga brmanfaat
untuk pecinta solder senusantara.
POLYTRON MINIMAX standby
POLYTRON MINIMAX standby
sempat di pusingkan ama tv
polytron stand by penggantian ic
program pun tak membuahkan
hasil akhirnya ketemu juga
penyebanya yaitu capasitor
keramik 15 pf dekat kristal c729
sempat di pusingkan ama tv
polytron stand by penggantian ic
program pun tak membuahkan
hasil akhirnya ketemu juga
penyebanya yaitu capasitor
keramik 15 pf dekat kristal c729
TB1226DN
TB1226DN
pin1 =EXT-VIDEO-IN
pin2 =V-AGC-FILTER
pin3 =H-VCC[9V]
pin4 =H-OUT
pin5 =CURY-CORRING
pin6 =FBP IN
pin7 =COINSIDENCE DET
pin8 =VDD[5V]
pin9 =SCL
pin10 =SDA
pin11 =DIGITAL-GND
pin12 =B OUT
pin13 =G OUT
pin14 =R OUT
pin15 =RGB GND
pin16 =ABCL
pin17 =RGB VCC[9V]
pin18 =R digital
pin19 =G digital
pin20 =B digital
pin21 =Ys/Ym
pin22 =Ys
pin23 =R analog
pin24 =G analog
pin25 =B analog
pin26 =COLOR LIMIT
pin27 =TV AUDIO IN
pin28 =EXT-AUDIO IN
pin29 =AUDIO OUT
pin30 =APC FILT
pin31 =Y2 IN
pin32 =FSC GND
pin33 =B-Y IN
pin34 =R-Y IN
pin35 =R-Y OUT
pin36 =B-Y OUT
pin37 =Y OUT
pin38 =FSC VCC[5V]
pin39 =BLACK FILT
pin40 =XTAL IN [16.2M]
pin41 =Y/C VCC[5V]
pin42 =CHR IN
pin43 =Y/C GND
pin44 =APL
pin45 =Y1 IN
pin46 =S-DEMODULATOR
pin47 =TV VIDEO IN
pin48 =AFC1
pin49 =SYNC OUT
pin50 =VERT SEPARATOR
pin51 =SYNC IN
pin52 =VERT RAMP
pin53 =VERT OUT
pin54 =VERT NF
pin55 =DEF GND
pin56 =VIDEO OUT
pin1 =EXT-VIDEO-IN
pin2 =V-AGC-FILTER
pin3 =H-VCC[9V]
pin4 =H-OUT
pin5 =CURY-CORRING
pin6 =FBP IN
pin7 =COINSIDENCE DET
pin8 =VDD[5V]
pin9 =SCL
pin10 =SDA
pin11 =DIGITAL-GND
pin12 =B OUT
pin13 =G OUT
pin14 =R OUT
pin15 =RGB GND
pin16 =ABCL
pin17 =RGB VCC[9V]
pin18 =R digital
pin19 =G digital
pin20 =B digital
pin21 =Ys/Ym
pin22 =Ys
pin23 =R analog
pin24 =G analog
pin25 =B analog
pin26 =COLOR LIMIT
pin27 =TV AUDIO IN
pin28 =EXT-AUDIO IN
pin29 =AUDIO OUT
pin30 =APC FILT
pin31 =Y2 IN
pin32 =FSC GND
pin33 =B-Y IN
pin34 =R-Y IN
pin35 =R-Y OUT
pin36 =B-Y OUT
pin37 =Y OUT
pin38 =FSC VCC[5V]
pin39 =BLACK FILT
pin40 =XTAL IN [16.2M]
pin41 =Y/C VCC[5V]
pin42 =CHR IN
pin43 =Y/C GND
pin44 =APL
pin45 =Y1 IN
pin46 =S-DEMODULATOR
pin47 =TV VIDEO IN
pin48 =AFC1
pin49 =SYNC OUT
pin50 =VERT SEPARATOR
pin51 =SYNC IN
pin52 =VERT RAMP
pin53 =VERT OUT
pin54 =VERT NF
pin55 =DEF GND
pin56 =VIDEO OUT
IC...IC...
TB1261N
pin1 =SIF IN/SECOND
pin2 =VCC IF/5V
pin3 =SIF IN
pin4 =SIF IN
pin5 =RF AGC
pin6 =IF IN
pin7 =IF IN
pin8 =IF AGC
pin9 =FM FILTER
pin10 =PIF FILTER
pin11 =X-TAL
pin12 =APC FILTER
pin13 =S FILTER
pin14 =VCC YC/5V
pin15 =R OUT
pin16 =G OUT
pin17 =B OUT
pin18 =YC GND
pin19 =VSM OUT
pin20 =Ysm
pin21 =OSD R
pin22 =OSD G
pin23 =OSD B
pin24 =RGB VCC/9V
pin25 =SCL
pin26 =SDA
pin27 =EHT IN
pin28 =ABCL
pin29 =EW OUT
pin30 =CW OUT
pin31 =DIGITAL VDD/9V
pin32 =SCP OUT
pin33 =H-OUT
pin34 =H AFC
pin35 =H-VCC/9V
pin36 =V-RAMP
pin37 =V-OUT
pin38 =DIGITAL GND
pin39 =Cb OUT
pin40 =Cr OUT
pin41 =Y OUT
pin42 =BLACK DET
pin43 =Y IN
pin44 =Cb-IN
pin45 =Cr-IN
pin46 =C-IN
pin47 =Ys
pin48 =V-IN
pin49 =DC RE
pin50 =DE-EMP
pin51 =VCC IF/9V
pin52 =DET OUT
pin53 =LOOP FILTER
pin54 =FM DC NF
pin55 =SIF OUT
pin56 =IF GND
TB 1227 DN
pin1 =VID-IN/SCP-OUT
pin2 =VAGC-FILTER
pin3 =H-VCC [5-9v]
pin4 =H-OUT
pin5 =CURVE CORRECTION
pin6 =FBP-IN
pin7 =COINCIDENT-DET
pin8 =VDD [5V]
pin9 =SCL
pin10 =SDA
pin11 =DIGITAL-GND
pin12 =B-OUT
pin13 =G-OUT
pin14 =R-OUT
pin15 =TEXT-GND
pin16 =ABCL
pin17 =RGB-VCC [9V]
pin18 =R-IN/DIGITAL
pin19 =G-IN/DIGITAL
pin20 =B-IN/DIGITAL
pin21 =YS-DIGITAL
pin22 =YS/YM/ANALOG
pin23 =R-IN/ANALOG
pin24 =G-IN/ANALOG
pin25 =B-IN/ANALOG
pin26 =COLOR-LIMITER
pin27 =TV/A-IN
pin28 =EXT-A-IN
pin29 =AUDIO=OUT/VSM-OUT
pin30 =APC-FILT
pin31 =Y-IN
pin32 =FSC-GND
pin33 =B-Y IN
pin34 =R-Y IN
pin35 =R-Y OUT
pin36 =B-Y OUT
pin37 =Y-OUT
pin38 =VDD-FSC [5V]
pin39 =BLACK STRETCH
pin40 =X-TAL/16.2MHZ
pin41 =Y/C-VCC [5V]
pin42 =CHROMA-IN
pin43 =Y/C-GND
pin44 =APL
pin45 =cvbs-in/VID-IN[COMPOSIT]
pin46 =SDEMO-ADJ
pin47 =TV-IN
pin48 =AFC1-FILT
pin49 =SYNC-OUT
pin50 =V-SEP A
pin51 =SYNC-IN
pin52 =V-RAMP
pin53 =V-OUT
pin54 =V-NF
pin55 =DEF-GND
pin56 =VID-OUT/VBLK-OUT
TB 1240 AN
pin1 =AFT OUT
pin2 =A.DE-EM
pin3 =VCC
pin4 =SIF IN
pin5 =IF GND
pin6 =IF IN
pin7 =IF IN
pin8 =RF AGC
pin9 =IF-AGC
pin10 =APC-FILT
pin11 =4.43MHZ
pin12 =Y/C GND
pin13 =YS/YM
pin14 =R IN
pin15 =G IN
pin16 =B IN
pin17 =RGB VCC [5.0]
pin18 =R OUT
pin19 =G OUT
pin20 =B OUT
pin21 =ABL
pin22 =V-RAMP
pin23 =V-NFB
pin24 =V-OUT
pin25 =V-AGC
pin26 =SCL
pin27 =SDA
pin28 =H-VCC [9.1]
pin29 =S-IO/CW-OUT
pin30 =FBP-IN
pin31 =SYNC-OUT
pin32 =H-OUT
pin33 =DEF-GND
pin34 =SCP-OUT
pin35 =E/W-OUT
pin36 =DIG-VCC [9.1]
pin37 =B-Y-IN
pin38 =R-Y-IN
pin39 =Y-IN
pin40 =H-AFC
pin41 =EHT-IN
pin42 =DIG-GND
pin43 =SYNC IN
pin44 =BLK DET
pin45 =C IN
pin46 =Y/C VCC [5.0]
pin47 =IF-DET-OUT
pin48 =LOOP-FILT
pin49 =VCO GND
pin50 =VCO
pin51 =VCO
pin52 =VCO-VCC []
pin53 =SIF
pin54 =RIPPLE
pin55 =SIF/H-PIN
pin56 =FM-DC-NF
TB 1227 AN
pin1 =VID-IN/SCP-OUT
pin2 =VAGC-FILTER
pin3 =H-VCC [5V]
pin4 =H-OUT
pin5 =CURVE CORRECTION
pin6 =FBP-IN
pin7 =COINCIDENT-DET
pin8 =VDD [5V]
pin9 =SCL
pin10 =SDA
pin11 =DIGITAL-GND
pin12 =B-OUT
pin13 =G-OUT
pin14 =R-OUT
pin15 =TEXT-GND
pin16 =ABCL
pin17 =RGB-VCC [9V]
pin18 =R-IN/DIGITAL
pin19 =G-IN/DIGITAL
pin20 =B-IN/DIGITAL
pin21 =YS-DIGITAL
pin22 =YS/YM/ANALOG
pin23 =R-IN/ANALOG
pin24 =G-IN/ANALOG
pin25 =B-IN/ANALOG
pin26 =COLOR-LIMITER
pin27 =TV/A-IN
pin28 =EXT-A-IN
pin29 =AUDIO=OUT/VSM-OUT
pin30 =APC-FILT
pin31 =Y-IN
pin32 =FSC-GND
pin33 =B-Y IN
pin34 =R-Y IN
pin35 =R-Y OUT
pin36 =B-Y OUT
pin37 =Y-OUT
pin38 =VDD-FSC [5V]
pin39 =BLACK STRETCH
pin40 =X-TAL/16MHZ
pin41 =Y/C-VCC [5V]
pin42 =CHROMA-IN
pin43 =Y/C-GND
pin44 =APL
pin45 =VID-IN/COMPOSIT
pin46 =SDEMO-ADJ
pin47 =TV-IN
pin48 =AFC1-FILT
pin49 =SYNC-OUT
pin50 =V-SEP A
pin51 =SYNC-IN
pin52 =V-RAMP
pin53 =V-OUT
pin54 =V-NF
pin55 =DEF-GND
pin56 =VID-OUT/VBLK-OUT
TB1251CN
pin1 =if-vcc
pin2 =ripple filter
pin3 =SIF OUT
pin4 =AUDIO OUT
pin5 =IF-GND
pin6 =IF-IN
pin7 =IF-IN
pin8 =RF-AGC
pin9 =09.1st SIF IN
pin10 =IF-AGC
pin11 =APC-FILTER
pin12 =XTAL [4.43MHZ]
pin13 =CW OUT
pin14 =RGB-VCC [9V]
pin15 =YS/YM SW
pin16 =R.IN [EXT]
pin17 =G IN [EXT]
pin18 =B IN [EXT]
pin19 =Y/C GND
pin20 =R OUT
pin21 =G OUT
pin22 =B OUT
pin23 =V,BIAS FILTER
pin24 =V.RAMP
pin25 =V.NFB
pin26 =V.OUT
pin27 =REF.R
pin28 =ABCL IN
pin29 =H AFC FILTER
pin30 =FBP IN/SCP OUT
pin31 =H.VCC[9V]
pin32 =H.OUT
pin33 =DIG GND
pin34 =SCL
pin35 =SDA
pin36 =BLACK DET
pin37 =DIG VDD
pin38 =SYNC IN
pin39 =Y IN
pin40 =DC RESTOR
pin41 =EW OUT
pin42 =Y/C VCC[5V]
pin43 =C IN
pin44 =Cr IN
pin45 =Cb IN
pin46 =VSM OUT
pin47 =
pin48 =EHT IN
pin49 =DE-EMPHASIS/MON.OUT
pin50 =RF TANK
pin51 =RF TANK
pin52 =DC NF
pin53 =VCO Bias Filter
pin54 =IF DET OUT
pin55 =AFT OUT
pin56 =SIF IN/Hcorr
pin1 =SIF IN/SECOND
pin2 =VCC IF/5V
pin3 =SIF IN
pin4 =SIF IN
pin5 =RF AGC
pin6 =IF IN
pin7 =IF IN
pin8 =IF AGC
pin9 =FM FILTER
pin10 =PIF FILTER
pin11 =X-TAL
pin12 =APC FILTER
pin13 =S FILTER
pin14 =VCC YC/5V
pin15 =R OUT
pin16 =G OUT
pin17 =B OUT
pin18 =YC GND
pin19 =VSM OUT
pin20 =Ysm
pin21 =OSD R
pin22 =OSD G
pin23 =OSD B
pin24 =RGB VCC/9V
pin25 =SCL
pin26 =SDA
pin27 =EHT IN
pin28 =ABCL
pin29 =EW OUT
pin30 =CW OUT
pin31 =DIGITAL VDD/9V
pin32 =SCP OUT
pin33 =H-OUT
pin34 =H AFC
pin35 =H-VCC/9V
pin36 =V-RAMP
pin37 =V-OUT
pin38 =DIGITAL GND
pin39 =Cb OUT
pin40 =Cr OUT
pin41 =Y OUT
pin42 =BLACK DET
pin43 =Y IN
pin44 =Cb-IN
pin45 =Cr-IN
pin46 =C-IN
pin47 =Ys
pin48 =V-IN
pin49 =DC RE
pin50 =DE-EMP
pin51 =VCC IF/9V
pin52 =DET OUT
pin53 =LOOP FILTER
pin54 =FM DC NF
pin55 =SIF OUT
pin56 =IF GND
TB 1227 DN
pin1 =VID-IN/SCP-OUT
pin2 =VAGC-FILTER
pin3 =H-VCC [5-9v]
pin4 =H-OUT
pin5 =CURVE CORRECTION
pin6 =FBP-IN
pin7 =COINCIDENT-DET
pin8 =VDD [5V]
pin9 =SCL
pin10 =SDA
pin11 =DIGITAL-GND
pin12 =B-OUT
pin13 =G-OUT
pin14 =R-OUT
pin15 =TEXT-GND
pin16 =ABCL
pin17 =RGB-VCC [9V]
pin18 =R-IN/DIGITAL
pin19 =G-IN/DIGITAL
pin20 =B-IN/DIGITAL
pin21 =YS-DIGITAL
pin22 =YS/YM/ANALOG
pin23 =R-IN/ANALOG
pin24 =G-IN/ANALOG
pin25 =B-IN/ANALOG
pin26 =COLOR-LIMITER
pin27 =TV/A-IN
pin28 =EXT-A-IN
pin29 =AUDIO=OUT/VSM-OUT
pin30 =APC-FILT
pin31 =Y-IN
pin32 =FSC-GND
pin33 =B-Y IN
pin34 =R-Y IN
pin35 =R-Y OUT
pin36 =B-Y OUT
pin37 =Y-OUT
pin38 =VDD-FSC [5V]
pin39 =BLACK STRETCH
pin40 =X-TAL/16.2MHZ
pin41 =Y/C-VCC [5V]
pin42 =CHROMA-IN
pin43 =Y/C-GND
pin44 =APL
pin45 =cvbs-in/VID-IN[COMPOSIT]
pin46 =SDEMO-ADJ
pin47 =TV-IN
pin48 =AFC1-FILT
pin49 =SYNC-OUT
pin50 =V-SEP A
pin51 =SYNC-IN
pin52 =V-RAMP
pin53 =V-OUT
pin54 =V-NF
pin55 =DEF-GND
pin56 =VID-OUT/VBLK-OUT
TB 1240 AN
pin1 =AFT OUT
pin2 =A.DE-EM
pin3 =VCC
pin4 =SIF IN
pin5 =IF GND
pin6 =IF IN
pin7 =IF IN
pin8 =RF AGC
pin9 =IF-AGC
pin10 =APC-FILT
pin11 =4.43MHZ
pin12 =Y/C GND
pin13 =YS/YM
pin14 =R IN
pin15 =G IN
pin16 =B IN
pin17 =RGB VCC [5.0]
pin18 =R OUT
pin19 =G OUT
pin20 =B OUT
pin21 =ABL
pin22 =V-RAMP
pin23 =V-NFB
pin24 =V-OUT
pin25 =V-AGC
pin26 =SCL
pin27 =SDA
pin28 =H-VCC [9.1]
pin29 =S-IO/CW-OUT
pin30 =FBP-IN
pin31 =SYNC-OUT
pin32 =H-OUT
pin33 =DEF-GND
pin34 =SCP-OUT
pin35 =E/W-OUT
pin36 =DIG-VCC [9.1]
pin37 =B-Y-IN
pin38 =R-Y-IN
pin39 =Y-IN
pin40 =H-AFC
pin41 =EHT-IN
pin42 =DIG-GND
pin43 =SYNC IN
pin44 =BLK DET
pin45 =C IN
pin46 =Y/C VCC [5.0]
pin47 =IF-DET-OUT
pin48 =LOOP-FILT
pin49 =VCO GND
pin50 =VCO
pin51 =VCO
pin52 =VCO-VCC []
pin53 =SIF
pin54 =RIPPLE
pin55 =SIF/H-PIN
pin56 =FM-DC-NF
TB 1227 AN
pin1 =VID-IN/SCP-OUT
pin2 =VAGC-FILTER
pin3 =H-VCC [5V]
pin4 =H-OUT
pin5 =CURVE CORRECTION
pin6 =FBP-IN
pin7 =COINCIDENT-DET
pin8 =VDD [5V]
pin9 =SCL
pin10 =SDA
pin11 =DIGITAL-GND
pin12 =B-OUT
pin13 =G-OUT
pin14 =R-OUT
pin15 =TEXT-GND
pin16 =ABCL
pin17 =RGB-VCC [9V]
pin18 =R-IN/DIGITAL
pin19 =G-IN/DIGITAL
pin20 =B-IN/DIGITAL
pin21 =YS-DIGITAL
pin22 =YS/YM/ANALOG
pin23 =R-IN/ANALOG
pin24 =G-IN/ANALOG
pin25 =B-IN/ANALOG
pin26 =COLOR-LIMITER
pin27 =TV/A-IN
pin28 =EXT-A-IN
pin29 =AUDIO=OUT/VSM-OUT
pin30 =APC-FILT
pin31 =Y-IN
pin32 =FSC-GND
pin33 =B-Y IN
pin34 =R-Y IN
pin35 =R-Y OUT
pin36 =B-Y OUT
pin37 =Y-OUT
pin38 =VDD-FSC [5V]
pin39 =BLACK STRETCH
pin40 =X-TAL/16MHZ
pin41 =Y/C-VCC [5V]
pin42 =CHROMA-IN
pin43 =Y/C-GND
pin44 =APL
pin45 =VID-IN/COMPOSIT
pin46 =SDEMO-ADJ
pin47 =TV-IN
pin48 =AFC1-FILT
pin49 =SYNC-OUT
pin50 =V-SEP A
pin51 =SYNC-IN
pin52 =V-RAMP
pin53 =V-OUT
pin54 =V-NF
pin55 =DEF-GND
pin56 =VID-OUT/VBLK-OUT
TB1251CN
pin1 =if-vcc
pin2 =ripple filter
pin3 =SIF OUT
pin4 =AUDIO OUT
pin5 =IF-GND
pin6 =IF-IN
pin7 =IF-IN
pin8 =RF-AGC
pin9 =09.1st SIF IN
pin10 =IF-AGC
pin11 =APC-FILTER
pin12 =XTAL [4.43MHZ]
pin13 =CW OUT
pin14 =RGB-VCC [9V]
pin15 =YS/YM SW
pin16 =R.IN [EXT]
pin17 =G IN [EXT]
pin18 =B IN [EXT]
pin19 =Y/C GND
pin20 =R OUT
pin21 =G OUT
pin22 =B OUT
pin23 =V,BIAS FILTER
pin24 =V.RAMP
pin25 =V.NFB
pin26 =V.OUT
pin27 =REF.R
pin28 =ABCL IN
pin29 =H AFC FILTER
pin30 =FBP IN/SCP OUT
pin31 =H.VCC[9V]
pin32 =H.OUT
pin33 =DIG GND
pin34 =SCL
pin35 =SDA
pin36 =BLACK DET
pin37 =DIG VDD
pin38 =SYNC IN
pin39 =Y IN
pin40 =DC RESTOR
pin41 =EW OUT
pin42 =Y/C VCC[5V]
pin43 =C IN
pin44 =Cr IN
pin45 =Cb IN
pin46 =VSM OUT
pin47 =
pin48 =EHT IN
pin49 =DE-EMPHASIS/MON.OUT
pin50 =RF TANK
pin51 =RF TANK
pin52 =DC NF
pin53 =VCO Bias Filter
pin54 =IF DET OUT
pin55 =AFT OUT
pin56 =SIF IN/Hcorr
LA 7688
LA7688
---------------------
pin1 =SIF IN
pin2 =RF AGC VR
pin3 =APC FILTER
pin4 =IF FILTER
pin5 =VCO COIL
pin6 =VCO COIL
pin7 =AFT OUT
pin8 =VIDEO OUT
pin9 =FILTER REF
pin10 =int.VIDEO
pin11 =CONT
pin12 =ext.A-IN
pin13 =SHARP
pin14 =ext.VIDEO
pin15 =GND
pin16 =VIDEO OUT
pin17 =COLOR
pin18 =TINT
pin19 =BRIGHT
pin20 =VERT OUT
pin21 =50/60
pin22 =AFC FILTER
pin23 =H OSC
pin24 =VCC-H
pin25 =H OUT
pin26 =FBP IN
pin27 =SB
pin30 =OSD G
pin31 =OSD R
pin32 =BLK STRECH
pin33 =B OUT
pin34 =G OUT
pin35 =R OUT
pin36 =ALC IN
pin37 =ALC IN
pin38 =DEMO OUT
pin39 =DEMO OUT
pin40 =VCC-v/c
pin41 =XTAL[3.58XXX]
pin42 =XTAL[3.58M]
pin43 =APC FILTER
pin44 =BIAS F
pin45 =VCC-VIF
pin46 =IF AGC
pin47 =VIF IN
pin48 =VIF IN
pin49 =GND
pin50 =RF AGC
pin51 =A OUT
pin52 =FM DET OUT
---------------------
pin1 =SIF IN
pin2 =RF AGC VR
pin3 =APC FILTER
pin4 =IF FILTER
pin5 =VCO COIL
pin6 =VCO COIL
pin7 =AFT OUT
pin8 =VIDEO OUT
pin9 =FILTER REF
pin10 =int.VIDEO
pin11 =CONT
pin12 =ext.A-IN
pin13 =SHARP
pin14 =ext.VIDEO
pin15 =GND
pin16 =VIDEO OUT
pin17 =COLOR
pin18 =TINT
pin19 =BRIGHT
pin20 =VERT OUT
pin21 =50/60
pin22 =AFC FILTER
pin23 =H OSC
pin24 =VCC-H
pin25 =H OUT
pin26 =FBP IN
pin27 =SB
pin30 =OSD G
pin31 =OSD R
pin32 =BLK STRECH
pin33 =B OUT
pin34 =G OUT
pin35 =R OUT
pin36 =ALC IN
pin37 =ALC IN
pin38 =DEMO OUT
pin39 =DEMO OUT
pin40 =VCC-v/c
pin41 =XTAL[3.58XXX]
pin42 =XTAL[3.58M]
pin43 =APC FILTER
pin44 =BIAS F
pin45 =VCC-VIF
pin46 =IF AGC
pin47 =VIF IN
pin48 =VIF IN
pin49 =GND
pin50 =RF AGC
pin51 =A OUT
pin52 =FM DET OUT
Minggu, 03 April 2011
LA 7687 A
LA7687A
-------------------------
pin1 =AV/SECAM[SIF IN]
pin2 =ID OUT
pin3 =APC1
pin4 =APC2
pin5 =VCO
pin6 =VCO adjust
pin7 =AFT OUT
pin8 =VIDEO OUT
pin9 =RF AGC
pin10 =internal VIDEO IN
pin11 =ACL IN
pin12 =FILTER REF[S-VHS SW]
pin13 =S-CHROMA DC CONTROL
pin14 =external VIDEO IN
pin15 =GND-y/c/d
pin16 =VIDEO OUT[ABL]
pin17 =COLOR KILLER
pin18 =ADDR
pin19 =DATA
pin20 =V-OUT[V-DRIVER]
pin21 =50/60HZ
pin22 =AFC FILTER
pin23 =H-OSC
pin24 =H-VCC[9V]
pin25 =H-OUT[H-DRIVE]
pin26 =FBP IN
pin27 =H-COINCIDENT[CLK OUT]
pin28 =BLK
pin29 =B IN
pin30 =G IN
pin31 =R IN
pin32 =-Y
pin33 =B OUT
pin34 =G OUT
pin35 =R OUT
pin36 =B-Y IN
pin37 =R-Y IN
pin38 =B-Y OUT
pin39 =R-Y OUT
pin40 =VCC-V/C[8V]
pin41 =CW2
pin42 =CW1
pin43 =APC FILTER
pin44 =VCC-SIF[9V]
pin45 =VCC-VIF[8V]
pin46 =IF AGC
pin47 =IF IN
pin48 =IF IN
pin49 =IF GND
pin50 =RF AGC
pin51 =AUDIO OUT
pin52 =AUDIO FILTER
-------------------------
pin1 =AV/SECAM[SIF IN]
pin2 =ID OUT
pin3 =APC1
pin4 =APC2
pin5 =VCO
pin6 =VCO adjust
pin7 =AFT OUT
pin8 =VIDEO OUT
pin9 =RF AGC
pin10 =internal VIDEO IN
pin11 =ACL IN
pin12 =FILTER REF[S-VHS SW]
pin13 =S-CHROMA DC CONTROL
pin14 =external VIDEO IN
pin15 =GND-y/c/d
pin16 =VIDEO OUT[ABL]
pin17 =COLOR KILLER
pin18 =ADDR
pin19 =DATA
pin20 =V-OUT[V-DRIVER]
pin21 =50/60HZ
pin22 =AFC FILTER
pin23 =H-OSC
pin24 =H-VCC[9V]
pin25 =H-OUT[H-DRIVE]
pin26 =FBP IN
pin27 =H-COINCIDENT[CLK OUT]
pin28 =BLK
pin29 =B IN
pin30 =G IN
pin31 =R IN
pin32 =-Y
pin33 =B OUT
pin34 =G OUT
pin35 =R OUT
pin36 =B-Y IN
pin37 =R-Y IN
pin38 =B-Y OUT
pin39 =R-Y OUT
pin40 =VCC-V/C[8V]
pin41 =CW2
pin42 =CW1
pin43 =APC FILTER
pin44 =VCC-SIF[9V]
pin45 =VCC-VIF[8V]
pin46 =IF AGC
pin47 =IF IN
pin48 =IF IN
pin49 =IF GND
pin50 =RF AGC
pin51 =AUDIO OUT
pin52 =AUDIO FILTER
IX 3311 CE
IX3311CE
----------------------
pin1 =POWER
pin2 =SCL
pin3 =SDA
pin4 =S-VOL
pin5 =EXIT BUS
pin6 =AV S-MUTE
pin7 =KEY IN
pin8 =PROTECT IN
pin9 =GND-VSSC/P
pin10 =POWER LED
pin11 =ST-BY LED
pin12 =GND-VSSA
pin13 =SECAM PLL
pin14 =VP2[8V]
pin15 =DEC DIG
pin16 =PH2 LF
pin17 =PH1 LF
pin18 =GND3
pin19 =DEC BG
pin20 =AVL
pin21 =VERT DRV A
pin22 =VERT DRV B
pin23 =IF IN1
pin24 =IF IN2
pin25 =VSC
pin26 =VERT IREF
pin27 =RF AGC OUT
pin28 =I-OUT[AUDIO DE-EMPHASIS]
pin29 =DEC S-DEM
pin30 =GND2
pin31 =SND PLL
pin32 =RE-OUT
pin33 =H DRV OUT
pin34 =FBin/SCP OUT
pin35 =ext AUDIO IN
pin36 =EHT
pin37 =PLL IF
pin38 =IF VIDEO OUT
pin39 =VP1[8V]
pin40 =int CVBS IN
pin41 =GND1
pin42 =ext CVBS IN
pin43 =C IN
pin44 =AUDIO OUT
pin45 =BLK2
pin46 =R2 IN
pin47 =G2 IN
pin48 =B2 IN
pin49 =BCL
pin50 =I BLACK
pin51 =R OUT
pin52 =G OUT
pin53 =B OUT
pin54 =VDDA[3.3V]
pin55 =VPE[GND]
pin56 =VDDC[3.3V]
pin57 =OSC
pin58 =XTAL IN [12M]
pin59 =XTAL OUT[12M]
pin60 =RESET
pin61 =VDDP[3.3V]
pin62 =SCL[eeprom]
pin63 =SDA[eeprom]
pin64 =R/C IN
----------------------
pin1 =POWER
pin2 =SCL
pin3 =SDA
pin4 =S-VOL
pin5 =EXIT BUS
pin6 =AV S-MUTE
pin7 =KEY IN
pin8 =PROTECT IN
pin9 =GND-VSSC/P
pin10 =POWER LED
pin11 =ST-BY LED
pin12 =GND-VSSA
pin13 =SECAM PLL
pin14 =VP2[8V]
pin15 =DEC DIG
pin16 =PH2 LF
pin17 =PH1 LF
pin18 =GND3
pin19 =DEC BG
pin20 =AVL
pin21 =VERT DRV A
pin22 =VERT DRV B
pin23 =IF IN1
pin24 =IF IN2
pin25 =VSC
pin26 =VERT IREF
pin27 =RF AGC OUT
pin28 =I-OUT[AUDIO DE-EMPHASIS]
pin29 =DEC S-DEM
pin30 =GND2
pin31 =SND PLL
pin32 =RE-OUT
pin33 =H DRV OUT
pin34 =FBin/SCP OUT
pin35 =ext AUDIO IN
pin36 =EHT
pin37 =PLL IF
pin38 =IF VIDEO OUT
pin39 =VP1[8V]
pin40 =int CVBS IN
pin41 =GND1
pin42 =ext CVBS IN
pin43 =C IN
pin44 =AUDIO OUT
pin45 =BLK2
pin46 =R2 IN
pin47 =G2 IN
pin48 =B2 IN
pin49 =BCL
pin50 =I BLACK
pin51 =R OUT
pin52 =G OUT
pin53 =B OUT
pin54 =VDDA[3.3V]
pin55 =VPE[GND]
pin56 =VDDC[3.3V]
pin57 =OSC
pin58 =XTAL IN [12M]
pin59 =XTAL OUT[12M]
pin60 =RESET
pin61 =VDDP[3.3V]
pin62 =SCL[eeprom]
pin63 =SDA[eeprom]
pin64 =R/C IN
IX 3564 CE
IX 3564 CE
------------------------
pin1 =POWER /3.3V
pin2 =SCL /4.3V
pin3 =SDA /4.3V
pin4 =MUTE /3.1V
pin5 =KEY2-EXIT /3.2V
pin6 =AV S-MUTE /3.2V
pin7 =KEY1-IN /3.2V
pin8 =PROT-IN /3.2V
pin9 =VSS-GND-C/P
pin10 =POWER LED /2.8V
pin11 =.../3.2V
pin12 =VSSA-GND
pin13 =SECAM PLL /2.1V
pin14 =VP2 [8V]
pin15 =DEC-DIG /4.6V
pin16 =PH2LF /2.6V
pin17 =PH1LF /3.5V
pin18 =GND3
pin19 =DEC-BG /3.7V
pin20 =AVL /2.1V
pin21 =VDRB /0V
pin22 =VDRA /0V
pin23 =IF-IN1 /1.7V
pin24 =IF-IN2 /1.7V
pin25 =VSC /3.5V
pin26 =VERT-IREF /3.5V
pin27 =RF-AGC-OUT /1V
pin28 =AUDIO-DEEM /2.9V
pin29 =DEC S-DEM /2.1V
pin30 =GND2
pin31 =SPLL /2.1V
pin32 =AV1/AV2-REOUT
pin33 =H-DRV OUT /1.2V
pin34 =FB-IN/SC-OUT /0.4V
pin35 =EXT.AUDIO-IN /3.3V
pin36 =EHT /0.7V
pin37 =PLL IF /2.5V
pin38 =IF-VIDEO-OUT /3.6V
pin39 =VP1 [8V]
pin40 =INT.CVBS-IN /3.6V
pin41 =GND1
pin42 =EXT.CVBS-IN /3V
pin43 =C-IN /1.3V
pin44 =AUDIO-OUT /3.1V
pin45 =BLK2 /0V
pin46 =R2-IN /2.3V
pin47 =G2-IN /2.3V
pin48 =B2-IN /2.3V
pin49 =BCL /3.5V
pin50 =IBLACK /7.6V
pin51 =R-OUT /1.7V
pin52 =G-OUT /1.9V
pin53 =B-OUT /2.1V
pin54 =VDDA [3.3V]
pin55 =VPE-GND
pin56 =VDDC [3.3V]
pin57 =osc /0V
pin58 =X-TAL IN /12MHZ
pin59 =X-TAL OUT/12MHZ
pin60 =reset /0V
pin61 =vddp [3.3v]
pin62 =SCL[eeprom] /4.6V
pin63 =SDA[eeprom] /4.6V
pin64 =RC-IN /3.8V
------------------------
pin1 =POWER /3.3V
pin2 =SCL /4.3V
pin3 =SDA /4.3V
pin4 =MUTE /3.1V
pin5 =KEY2-EXIT /3.2V
pin6 =AV S-MUTE /3.2V
pin7 =KEY1-IN /3.2V
pin8 =PROT-IN /3.2V
pin9 =VSS-GND-C/P
pin10 =POWER LED /2.8V
pin11 =.../3.2V
pin12 =VSSA-GND
pin13 =SECAM PLL /2.1V
pin14 =VP2 [8V]
pin15 =DEC-DIG /4.6V
pin16 =PH2LF /2.6V
pin17 =PH1LF /3.5V
pin18 =GND3
pin19 =DEC-BG /3.7V
pin20 =AVL /2.1V
pin21 =VDRB /0V
pin22 =VDRA /0V
pin23 =IF-IN1 /1.7V
pin24 =IF-IN2 /1.7V
pin25 =VSC /3.5V
pin26 =VERT-IREF /3.5V
pin27 =RF-AGC-OUT /1V
pin28 =AUDIO-DEEM /2.9V
pin29 =DEC S-DEM /2.1V
pin30 =GND2
pin31 =SPLL /2.1V
pin32 =AV1/AV2-REOUT
pin33 =H-DRV OUT /1.2V
pin34 =FB-IN/SC-OUT /0.4V
pin35 =EXT.AUDIO-IN /3.3V
pin36 =EHT /0.7V
pin37 =PLL IF /2.5V
pin38 =IF-VIDEO-OUT /3.6V
pin39 =VP1 [8V]
pin40 =INT.CVBS-IN /3.6V
pin41 =GND1
pin42 =EXT.CVBS-IN /3V
pin43 =C-IN /1.3V
pin44 =AUDIO-OUT /3.1V
pin45 =BLK2 /0V
pin46 =R2-IN /2.3V
pin47 =G2-IN /2.3V
pin48 =B2-IN /2.3V
pin49 =BCL /3.5V
pin50 =IBLACK /7.6V
pin51 =R-OUT /1.7V
pin52 =G-OUT /1.9V
pin53 =B-OUT /2.1V
pin54 =VDDA [3.3V]
pin55 =VPE-GND
pin56 =VDDC [3.3V]
pin57 =osc /0V
pin58 =X-TAL IN /12MHZ
pin59 =X-TAL OUT/12MHZ
pin60 =reset /0V
pin61 =vddp [3.3v]
pin62 =SCL[eeprom] /4.6V
pin63 =SDA[eeprom] /4.6V
pin64 =RC-IN /3.8V
AN 5601K
AN 5601 K
TV SIGNAL PROCESSOR
pin1=.GND
pim2=.chr vco
pim3=.color control
pim4=.acc filt
pim5=.chr signal in
pim6=.contras color
pim7=.acc amp out
pim8=.apc1
pim9=.apc2
pim10=.vcc[5v]
pim11=.R-Y in
pim12=.color killer filt
pim13=.B-Y in
pim14=.data blanking
pim15=.video in1
pim16=.video in2
pim17=.pic control
pim18=.brightness control
pim19=.B out
pim20=.G out
pim21=.original G
pim22=.ext G
pim23=.ext B
pim24=.original B
pim25=.original R
pim26=.out R
pim27=.ext R
pim28=.sync.separation clamp
pim29=.vcc1[12v]
pim30=.sync.separation filt
pim31=.V out
pim32=.feedbck in
pim33=.V osc
pim34=.Vdrv
pim35=.Vintegration
pim36=.SCPout
pim37=.FBPin
pim38=.Hafc out
pim39=.Hosc
pim40=.Hcenter adj.
pim41=.Hout
pim42=.VCC3/H[8,6v
TV SIGNAL PROCESSOR
pin1=.GND
pim2=.chr vco
pim3=.color control
pim4=.acc filt
pim5=.chr signal in
pim6=.contras color
pim7=.acc amp out
pim8=.apc1
pim9=.apc2
pim10=.vcc[5v]
pim11=.R-Y in
pim12=.color killer filt
pim13=.B-Y in
pim14=.data blanking
pim15=.video in1
pim16=.video in2
pim17=.pic control
pim18=.brightness control
pim19=.B out
pim20=.G out
pim21=.original G
pim22=.ext G
pim23=.ext B
pim24=.original B
pim25=.original R
pim26=.out R
pim27=.ext R
pim28=.sync.separation clamp
pim29=.vcc1[12v]
pim30=.sync.separation filt
pim31=.V out
pim32=.feedbck in
pim33=.V osc
pim34=.Vdrv
pim35=.Vintegration
pim36=.SCPout
pim37=.FBPin
pim38=.Hafc out
pim39=.Hosc
pim40=.Hcenter adj.
pim41=.Hout
pim42=.VCC3/H[8,6v
AN 5192K A
AN 5192 K-A
-------------------------
pin1 =R CLAMP
pin2 =G CLAMP
pin3 =B CLAMP
pin4 =KILLER FILTER
pin5 =KILLER OUTPUT
pin6 =APC FILTER
pin7 =4.43
pin8 =3.58
pin9 =SPOT KILLER
pin10 =BLK IN
pin11 =R IN
pin12 =G IN
pin13 =B IN
pin14 =VCC [9V]
pin15 =R OUT
pin16 =G OUT
pin17 =B OUT
pin18 =LOCK DET
pin19 =GND
pin20 =ACL
pin21 =SDA
pin22 =SCL
pin23 =VCC [5V]
pin24 =IF IN
pin25 =IF IN
pin26 =GND
pin27 =RF AGC
pin28 =AUDIO OUT
pin29 =DE-EMPHASIS
pin30 =AFT OUT
pin31 =VIDEO IN
pin32 =DECOP
pin33 =AV AUDIO IN
pin34 =SIF IN
pin35 =IF AGC
pin36 =VIDEO OUT
pin37 =APC2
pin38 =VIDEO DET IN
pin39 =DET OUT
pin40 =APC1
pin41 =VCO
pin42 =BLACK DET
pin43 =Y-IN
pin44 =V-CLAMP
pin45 =V-SEPARATION
pin46 =H-SEPARATION
pin47 =VCC [5V]
pin48 =CHROMA IN
pin49 =GND
pin50 =FBT IN
pin51 =H VCC [20V]
pin52 =AFC2 FILT
pin53 =AFC1 FILT
pin54 =H OSC
pin55 =X-RAY
pin56 =H OUT
pin57 =50/60 DET OUT
pin58 =V OUT
pin59 =CW
pin60 =B-Y OUT
pin61 =R-Y OUT
pin62 =SCP
pin63 =B-Y IN
pin64 =R-Y IN
-------------------------
pin1 =R CLAMP
pin2 =G CLAMP
pin3 =B CLAMP
pin4 =KILLER FILTER
pin5 =KILLER OUTPUT
pin6 =APC FILTER
pin7 =4.43
pin8 =3.58
pin9 =SPOT KILLER
pin10 =BLK IN
pin11 =R IN
pin12 =G IN
pin13 =B IN
pin14 =VCC [9V]
pin15 =R OUT
pin16 =G OUT
pin17 =B OUT
pin18 =LOCK DET
pin19 =GND
pin20 =ACL
pin21 =SDA
pin22 =SCL
pin23 =VCC [5V]
pin24 =IF IN
pin25 =IF IN
pin26 =GND
pin27 =RF AGC
pin28 =AUDIO OUT
pin29 =DE-EMPHASIS
pin30 =AFT OUT
pin31 =VIDEO IN
pin32 =DECOP
pin33 =AV AUDIO IN
pin34 =SIF IN
pin35 =IF AGC
pin36 =VIDEO OUT
pin37 =APC2
pin38 =VIDEO DET IN
pin39 =DET OUT
pin40 =APC1
pin41 =VCO
pin42 =BLACK DET
pin43 =Y-IN
pin44 =V-CLAMP
pin45 =V-SEPARATION
pin46 =H-SEPARATION
pin47 =VCC [5V]
pin48 =CHROMA IN
pin49 =GND
pin50 =FBT IN
pin51 =H VCC [20V]
pin52 =AFC2 FILT
pin53 =AFC1 FILT
pin54 =H OSC
pin55 =X-RAY
pin56 =H OUT
pin57 =50/60 DET OUT
pin58 =V OUT
pin59 =CW
pin60 =B-Y OUT
pin61 =R-Y OUT
pin62 =SCP
pin63 =B-Y IN
pin64 =R-Y IN
samsung
Setting DEFLECTION tv SAMSUNG
U-Slim 29 inch
V. Amp_15
V. Shift_-40
H. EW_88
H. Shift_118
V. Lin_0
V.SC_43
H.Parabola_82
Upper Corner_-35
Lower Corner_-43
Upper Corner6_9
Lower Corner6_10
H. Trapezium_5
Bow_1
Angle_1
EHT Time_20
EHT Threshold_1
EHT Vertical_-60
EHT Horizontal_-20
EHT Vertical2_-15
EHT Horizontal2_10
U-Slim 29 inch
V. Amp_15
V. Shift_-40
H. EW_88
H. Shift_118
V. Lin_0
V.SC_43
H.Parabola_82
Upper Corner_-35
Lower Corner_-43
Upper Corner6_9
Lower Corner6_10
H. Trapezium_5
Bow_1
Angle_1
EHT Time_20
EHT Threshold_1
EHT Vertical_-60
EHT Horizontal_-20
EHT Vertical2_-15
EHT Horizontal2_10
polytron minimax nicam
Polytron Minimax nicam &
zweiton stereo + subwoofer.
op0= 10111011
op1= 11001110
op2= 11000011
op3= 00000110
Polytron DIVA option setting
polytron DIVA flat, subwoofer, uC
= HBT-00-02G
op0= 0100 1011
op1= 1101 1010
op2= 0110 1001
op3= 0001 1101
option setting Polytron DIVA flat,
subwoofer + FM radio model
PS-5225, uC= HBT-00-04G
op0= 0110 0001
op1= 1101 0010
op2= 0000 1001
op3= 0000 1101
op4= 0001 0011
op5= 0000 0000
POLYTRON MX1503-RIW+RADIO
OPTION0:00000001 01H
OPTION1:10010010 92H
OPTION2:00001001 09H
OPTION3:00001101 0DH
OPTION4:00010000 10H
OPTION5:00000000 00H
OPTLANG:00000001 01H
1. BUILT- IN FM RADIO
2. FSM (FIEL STRENGTH METER)
3. SUBWOOFER OUTPUT
4. AV MULTI SYSTEM
Polytron L-cidi
0ption Lang 00000001 01H,
Option5 00011010 1AH,
Option4 00010000 10H,
Option3 00001001 09H,
Option2 00001001 09H,
Option1 10000010 82H,
Option0 00000101 05H.
MX-5202, HBT-00-04G
0100 0001
1001 0010
0000 1001
0000 1100
0001 0000
0000 0000
0000 0001
MX-5266, HBM-01-04, pakai VCD,
sub woofer, nicam, flat biasa
1111 1011
1000 1110
0001 0010
PS-5225, HBT-00-04G, DIVA,
subwoofer
0110 0001
1101 0010
0000 1001
0000 1101
0001 0011
0000 0000
HBT-00-02G, DIVA, subwoofer
0100 1011
1101 1010
0110 1001
0001 1101
PS-52SV60, HBT-00-04G, slim, fm,
subwoofer
65
C8
19
0D
13
MX-51P65, ....., DIPE, NICAM
STEREO
1011 1011
1100 1110
1100 0011
0000 0110
POLYTRON PN20123KA OPTION
BIT HBK-00-01
OPTION0 11011011
OPTION1 11111101
OPTION2 11000011
OPTION3 11111110
HBT-00-01G Polytron MX
minimax
OPTION0 01000011
OPTION1 10011010
OPTION2 00001001
OPTION3 00011100
aktifkan radio FM UBAH OPTION3
0000 1101
POLYTRON MX HBM-00-01H
OPTION0 01011001
OPTION1 00000011
OPTION2 11000011
OPTION3 00001000
OPTION 0
1. AV1
2. AV2
3. DVD
4. SUBWOOFER
5. BAZZOKE
6. IC TONE
7. STEREO
8. S-VHS
OPTION 1
1. DIGITEC\POLYTRON
2. LOGO OFF\POLYTRON
3. MENU OFF
4. AVL
5. ZOOM
6. NICAM/A2/M/S
7. DIVA
8. SURROUND
catatan untuk bit 1 dan 2 adalah
kombinasi untuk brand
option : 00=polytron
01=digitec
11=tanpa merk (polos)
10=polytron (kalau dulu merk OK)
OPTION 2
1. SOUND SYTEM BG
2. I
3. DK
4. M
5. DIPE\DIGITAL INTELIGENT
6. DIPE\PICTURE ENHANCE
7. DIVA\DIGITAL INTELIGENT
8. DIVA\VIDEO AMPLIFIER
untu bit 5,6,7,8 : 1100=DIPE
digital inteligent picture
enhance :1111=DIVA digital
inteligent picture enhance
OPTION 3
1. FM RADIO
2. LANGUAGE
3. MUSIC MODE
4. FS METER
5. OPTION
6. OPTION
7. OPTION
8. OPTION
zweiton stereo + subwoofer.
op0= 10111011
op1= 11001110
op2= 11000011
op3= 00000110
Polytron DIVA option setting
polytron DIVA flat, subwoofer, uC
= HBT-00-02G
op0= 0100 1011
op1= 1101 1010
op2= 0110 1001
op3= 0001 1101
option setting Polytron DIVA flat,
subwoofer + FM radio model
PS-5225, uC= HBT-00-04G
op0= 0110 0001
op1= 1101 0010
op2= 0000 1001
op3= 0000 1101
op4= 0001 0011
op5= 0000 0000
POLYTRON MX1503-RIW+RADIO
OPTION0:00000001 01H
OPTION1:10010010 92H
OPTION2:00001001 09H
OPTION3:00001101 0DH
OPTION4:00010000 10H
OPTION5:00000000 00H
OPTLANG:00000001 01H
1. BUILT- IN FM RADIO
2. FSM (FIEL STRENGTH METER)
3. SUBWOOFER OUTPUT
4. AV MULTI SYSTEM
Polytron L-cidi
0ption Lang 00000001 01H,
Option5 00011010 1AH,
Option4 00010000 10H,
Option3 00001001 09H,
Option2 00001001 09H,
Option1 10000010 82H,
Option0 00000101 05H.
MX-5202, HBT-00-04G
0100 0001
1001 0010
0000 1001
0000 1100
0001 0000
0000 0000
0000 0001
MX-5266, HBM-01-04, pakai VCD,
sub woofer, nicam, flat biasa
1111 1011
1000 1110
0001 0010
PS-5225, HBT-00-04G, DIVA,
subwoofer
0110 0001
1101 0010
0000 1001
0000 1101
0001 0011
0000 0000
HBT-00-02G, DIVA, subwoofer
0100 1011
1101 1010
0110 1001
0001 1101
PS-52SV60, HBT-00-04G, slim, fm,
subwoofer
65
C8
19
0D
13
MX-51P65, ....., DIPE, NICAM
STEREO
1011 1011
1100 1110
1100 0011
0000 0110
POLYTRON PN20123KA OPTION
BIT HBK-00-01
OPTION0 11011011
OPTION1 11111101
OPTION2 11000011
OPTION3 11111110
HBT-00-01G Polytron MX
minimax
OPTION0 01000011
OPTION1 10011010
OPTION2 00001001
OPTION3 00011100
aktifkan radio FM UBAH OPTION3
0000 1101
POLYTRON MX HBM-00-01H
OPTION0 01011001
OPTION1 00000011
OPTION2 11000011
OPTION3 00001000
OPTION 0
1. AV1
2. AV2
3. DVD
4. SUBWOOFER
5. BAZZOKE
6. IC TONE
7. STEREO
8. S-VHS
OPTION 1
1. DIGITEC\POLYTRON
2. LOGO OFF\POLYTRON
3. MENU OFF
4. AVL
5. ZOOM
6. NICAM/A2/M/S
7. DIVA
8. SURROUND
catatan untuk bit 1 dan 2 adalah
kombinasi untuk brand
option : 00=polytron
01=digitec
11=tanpa merk (polos)
10=polytron (kalau dulu merk OK)
OPTION 2
1. SOUND SYTEM BG
2. I
3. DK
4. M
5. DIPE\DIGITAL INTELIGENT
6. DIPE\PICTURE ENHANCE
7. DIVA\DIGITAL INTELIGENT
8. DIVA\VIDEO AMPLIFIER
untu bit 5,6,7,8 : 1100=DIPE
digital inteligent picture
enhance :1111=DIVA digital
inteligent picture enhance
OPTION 3
1. FM RADIO
2. LANGUAGE
3. MUSIC MODE
4. FS METER
5. OPTION
6. OPTION
7. OPTION
8. OPTION
polytron
Option dan Setting
OPTION setting tv POLYTRON
KODE 1013
H - SHIFT 6
H - BROW 4
H - PARA 7
S - COR 27
V - LIN 15
B - DRIV 80
G - DRIV 50
B - CUT 167
G - CUT 32
R - CUT 10
V - AMP 38
V - CENT 16
KODE 1014
AGC GAIN 44
OPTION 0 01001011
OPTION 1 01001000
OPTION 2 00011001
OPTION 3 00001101
H - OSD 17
V - OSD 20
V - SHIFT 0
U - BLK 5
V - BLK 5
BRTS 4
Y - DELAY 7
WBBRI 70
WBCON 100
WBCOL 50
LO AGC 38
HI AGC 39
KODE 1207
CTS 16
FS-SLV 92
FS-CTR 136
FS-BVL 1
FS-BVH 2
FS-BUH 8
FS-LOMIN 42
FS-HIMIN 6
FS-LOVL 100
FS-HIVL 14
FS-LOVH 100
FS-HIVH 36
FS-LOUH 58
FS-HIUH 71
STEP TV 40
SHP-PAR 75
SS 100 10101101
SS 80 10101000
SS 60 11011110
SS 40 01010100
SS 20 01001010
SS 0 01000000
F-LIM HI 56
F- LIM LO 30
ALGO 1
BOST H 69
BOST L 35
DIV 4
IF-MIN 76
IFMAX 116
RF-MAX 45
BOSTER 11000010
KODE 1206
SCNT 10
CNTX 127
CNTC 64
CNTN 0
CNTD 127
BRTX 42
BRTC 76
BRTN 32
COLX 80
COLC 58
COLN 13
COLP 58
COLD 61
TNTX 61
TNTC 66
TNTN 40
ST3 28
SV3 34
ST4 28
SV4 34
SVD 25
SHPX 29
SHPN 10
ASSH 6
ABCL 00000001
DCBS 00000111
OSDA 00000010
NOIS 00001111
NDCT 31
FLG 0 01000100
FLG 1 00000000
SVM 00010000
VBKL 00000000
VCD 0 00011010
VCD 1 00000001
VL 1 37
VL 50 95
T COL 10001011
B COL 01110101
ST BG 2
ST I 2
ST DK 2
ST M 2
SSBG 00001110
SS I 00001110
SS DK 00001110
SS M 00000001
SYNC 10000010
HSFC 10000100
ALC 3
VOLCP 73
MUTT 55
TINTPAL 58
DMP 0
NCOMB
OPTION setting tv POLYTRON
KODE 1013
H - SHIFT 6
H - BROW 4
H - PARA 7
S - COR 27
V - LIN 15
B - DRIV 80
G - DRIV 50
B - CUT 167
G - CUT 32
R - CUT 10
V - AMP 38
V - CENT 16
KODE 1014
AGC GAIN 44
OPTION 0 01001011
OPTION 1 01001000
OPTION 2 00011001
OPTION 3 00001101
H - OSD 17
V - OSD 20
V - SHIFT 0
U - BLK 5
V - BLK 5
BRTS 4
Y - DELAY 7
WBBRI 70
WBCON 100
WBCOL 50
LO AGC 38
HI AGC 39
KODE 1207
CTS 16
FS-SLV 92
FS-CTR 136
FS-BVL 1
FS-BVH 2
FS-BUH 8
FS-LOMIN 42
FS-HIMIN 6
FS-LOVL 100
FS-HIVL 14
FS-LOVH 100
FS-HIVH 36
FS-LOUH 58
FS-HIUH 71
STEP TV 40
SHP-PAR 75
SS 100 10101101
SS 80 10101000
SS 60 11011110
SS 40 01010100
SS 20 01001010
SS 0 01000000
F-LIM HI 56
F- LIM LO 30
ALGO 1
BOST H 69
BOST L 35
DIV 4
IF-MIN 76
IFMAX 116
RF-MAX 45
BOSTER 11000010
KODE 1206
SCNT 10
CNTX 127
CNTC 64
CNTN 0
CNTD 127
BRTX 42
BRTC 76
BRTN 32
COLX 80
COLC 58
COLN 13
COLP 58
COLD 61
TNTX 61
TNTC 66
TNTN 40
ST3 28
SV3 34
ST4 28
SV4 34
SVD 25
SHPX 29
SHPN 10
ASSH 6
ABCL 00000001
DCBS 00000111
OSDA 00000010
NOIS 00001111
NDCT 31
FLG 0 01000100
FLG 1 00000000
SVM 00010000
VBKL 00000000
VCD 0 00011010
VCD 1 00000001
VL 1 37
VL 50 95
T COL 10001011
B COL 01110101
ST BG 2
ST I 2
ST DK 2
ST M 2
SSBG 00001110
SS I 00001110
SS DK 00001110
SS M 00000001
SYNC 10000010
HSFC 10000100
ALC 3
VOLCP 73
MUTT 55
TINTPAL 58
DMP 0
NCOMB
Jumat, 01 April 2011
Fello Elektronick protek mode
Sharp
Chasis UA-1, Menggunakan IC
IX3368CEN1-5 Atau IX3410CEN1-5
Masukan Proteksi Detektor Yang
Dideteksi Tegangan Normal
Menonaktifkan Proteksi
Pin No.8 IC801 (3,3 V)
Menonaktifkan Proteksi utama,
Lepaskan Jumper J223
D609 Tegangan 8V Anoda D609 =
3.3 Volt Lepaskan D609
D606 ABL / X-ray Anoda D606 =
3.3 Volt Lepaskan D606
D614, Q603 Heater / X-ray Anoda
D614 = 3.3 Volt
Collector Q603 = 3.3 Volt Lepaskan
D614
Lepaskan Q603
D752 Tegangan 5V Anoda D752 =
3.3 Volt Lepaskan D752
D504 Tegangan 16V (Sound Amp)
Anoda D504 = 3.3 Volt Lepaskan
D504
D502 Tegangan 45V (Vertikal)
Anoda D502 = 3.3 Volt Lepaskan
D502
D503 Vertikal Output Anoda D503
= 3.3 Volt Lepaskan D503
D613 Tegangan 180V Anoda
D613 = 3.3 Volt Lepaskan D613
Chasis UA-1 (Lubang),
Menggunakan IC IX3368CEN7
Masukan Proteksi Detektor Yang
Dideteksi Tegangan Normal
Menonaktifkan Proteksi
Pin No.8 IC801 (3,4 V)
Menonaktifkan Proteksi utama,
Lepaskan Jumper J208 dan D203
D203 Tegangan 33V (Tuner)
Anoda D203 = 3.4 Volt Lepaskan
D203
D607 Tegangan 190V Anoda
D607 = 3.4 Volt Lepaskan D607
D604, Q603 Heater / X-ray Anoda
D604 = 3.4 Volt
Collector Q603 = 3.4 Volt Lepaskan
D604
Lepaskan Q603
D601 ABL / X-ray Anoda D601 =
3.4 Volt Lepaskan D601
Q501 Tegangan Supply Vertikal
Collector Q501 = 3.4 Volt Lepaskan
D501
Menggunakan IC IX 2938CE,
TB1226
Masukan Proteksi Detektor Yang
Dideteksi Tegangan Normal
Menonaktifkan Proteksi
Pin No.30 IC1001 (5,1 V) D616
Tegangan 9V Anoda D616 = 5.1
Volt Lepaskan D616
D607 Tegangan 180V Anoda
D607 = 5.1 Volt Lepaskan D607
Q607 Heater / X-ray Collector
Q607 = 5.1 Volt Lepaskan Q607
D606 ABL / X-ray Anoda D606 =
5.1 Volt Lepaskan D606
D611 Tegangan 5V Anoda D611 =
5.1 Volt Lepaskan D611
D201 Tegangan 9V Anoda D201 =
5.1 Volt Lepaskan D201
Menggunakan IC IX 2694, M52340
Masukan Proteksi Detektor Yang
Dideteksi Tegangan Normal
Menonaktifkan Proteksi
Pin No.38 IC1001 (0 V) D606
Heater / X-ray Anoda D606 = 0
Volt Lepaskan D606
D616 ABL / X-ray Anoda D616 = 0
Volt Lepaskan D616
Q603 ABL / X-ray Collector Q603 =
0 Volt Lepaskan Q603
D610 Heater / X-ray Anoda D610 =
0 Volt Lepaskan D610
Chasis G2 Menggunakan IC IX
3031CE, TB1226
Masukan Proteksi Detektor Yang
Dideteksi Tegangan Normal
Menonaktifkan Proteksi
Pin No.30 IC1001 (3,3 V) D618
Tegangan 9V Anoda D618 = 3,3
Volt Lepaskan D618
D607 Heater / X-ray Anoda D607 =
3,3 Volt Lepaskan D607
Q607 Heater / X-ray Collector
Q607 = 3,3 Volt Lepaskan Q607
D606 ABL / X-ray Anoda D606 =
3,3 Volt Lepaskan D606
D611 Tegangan 5V Anoda D611 =
3,3 Volt Lepaskan D611
GA-4M Chasis, Menggunakan IC
IXB226WJ, M61260
Masukan Proteksi Detektor Yang
Dideteksi Tegangan Normal
Menonaktifkan Proteksi
Pin No.7 IC1001 (4.5 V) D605
Tegangan 185V Anoda D605 = 4,5
Volt Lepaskan D605
D608 ABL / X-ray Katoda D607 =
4,5 Volt Lepaskan D608
Q603 Heater Collector Q603 = 4,5
Volt Lepaskan Q603
D203 Tegangan 33V (Tuner)
Anoda D203 = 4,5 Volt Lepaskan
D203
D1091 Tegangan 9V Anoda D606
= 4,5 Volt Lepaskan D1091
Pin No.6 IC1001 (3.4 V)
D1010 Tegangan 15V Pin No.6
IC1001 = 3.4 Volt Lepaskan D1010
Chasis GA-6, Menggunakan IC
IXB725WJ, Chasis GA-7
Menggunakan IC IXB855WJZZ
Masukan Proteksi Detektor Yang
Dideteksi Tegangan Normal
Menonaktifkan Proteksi
Pin No.63 IC801 (4.1 V) D1005
Tegangan 9V Anoda D1005 = 4,1
Volt Lepaskan D1005
D608 ABL / X-ray Katoda D608 =
4,1 Volt Lepaskan D608
Q603 Heater Collector Q603 = 4,1
Volt Lepaskan Q603
D805, D203 Tegangan 33V
(Tuner) Anoda D805 & D203 = 4,1
Volt Lepaskan D203
D204 Tegangan 5V (Tuner) Anoda
D204 = 4,1 Volt Lepaskan D204
Pin No.7 IC801 (3.9 V) D1002
Power supply (AC-Detect) Pin No.7
IC801 = 3.9 Volt Lepaskan D1002
Pin No.8 IC801 (0.6 V) R523
Vertical Pin No.8 IC801 = 0.6 Volt
Lepaskan R523
Menggunakan IC IXC080WJN5Q
Masukan Proteksi Detektor Yang
Dideteksi Tegangan Normal
Menonaktifkan Proteksi
Pin No.63 IC801 (4.1 V)
Menonaktifkan Proteksi utama,
Lepaskan Jumper J497
D1108 Tegangan 5V Anoda
D1008 = 4,1 Volt Lepaskan D1108
D605 Tegangan 185V Katoda
D605 = 4,1 Volt Lepaskan D605
D608, D607 ABL / X-ray Katoda
D608 = 4,1 Volt Lepaskan D608
Q603, D604 Heater / X-ray
Collector Q603 = 4,1 Volt Lepaskan
Q603
D203 Tegangan 33V (Tuner)
Anoda D203 = 4,1 Volt Lepaskan
D203
D1105 Tegangan 5V Anoda
D1105 = 4,1 Volt Lepaskan D1105
Pin No.64 IC801 (3.9 V) D1002
Power supply (AC-Detect) Pin
No.64 IC801 = 3.9 Volt Lepaskan
D1002
Pin No.65 IC801 (0.6 V) R523
Vertical Pin No.65 IC801 = 0.6 Volt
Lepaskan R523
Menggunakan IC IXC688WJ / IC
IXC844WJ
Masukan Proteksi Detektor Yang
Dideteksi Tegangan Normal
Menonaktifkan Proteksi
Pin No.81 IC801 (4.1 V)
D1108 Tegangan 5V Anoda
D1008 = 4,1 Volt Lepaskan D1108
D605 Tegangan 185V Katoda
D605 = 4,1 Volt Lepaskan D605
D608, D607 ABL / X-ray Katoda
D608 = 4,1 Volt Lepaskan D608
Q603, D604 Heater / X-ray
Collector Q603 = 4,1 Volt Lepaskan
Q603
D203 Tegangan 33V (Tuner)
Anoda D203 = 4,1 Volt Lepaskan
D203
D1105 Tegangan 5V Anoda
D1105 = 4,1 Volt Lepaskan D1105
Pin No.82 IC801 (3.9 V) D1002
Power supply (AC-Detect) Pin
No.82 IC801 = 3.9 Volt Lepaskan
D1002
Pin No.83 IC801 (0.6 V) R523
Vertical Pin No.83 IC801 = 0.6 Volt
Lepaskan R523
Sharp
Chasis UA-1, Menggunakan IC
IX3368CEN1-5 Atau IX3410CEN1-5
Masukan Proteksi Detektor Yang
Dideteksi Tegangan Normal
Menonaktifkan Proteksi
Pin No.8 IC801 (3,3 V)
Menonaktifkan Proteksi utama,
Lepaskan Jumper J223
D609 Tegangan 8V Anoda D609 =
3.3 Volt Lepaskan D609
D606 ABL / X-ray Anoda D606 =
3.3 Volt Lepaskan D606
D614, Q603 Heater / X-ray Anoda
D614 = 3.3 Volt
Collector Q603 = 3.3 Volt Lepaskan
D614
Lepaskan Q603
D752 Tegangan 5V Anoda D752 =
3.3 Volt Lepaskan D752
D504 Tegangan 16V (Sound Amp)
Anoda D504 = 3.3 Volt Lepaskan
D504
D502 Tegangan 45V (Vertikal)
Anoda D502 = 3.3 Volt Lepaskan
D502
D503 Vertikal Output Anoda D503
= 3.3 Volt Lepaskan D503
D613 Tegangan 180V Anoda
D613 = 3.3 Volt Lepaskan D613
Chasis UA-1 (Lubang),
Menggunakan IC IX3368CEN7
Masukan Proteksi Detektor Yang
Dideteksi Tegangan Normal
Menonaktifkan Proteksi
Pin No.8 IC801 (3,4 V)
Menonaktifkan Proteksi utama,
Lepaskan Jumper J208 dan D203
D203 Tegangan 33V (Tuner)
Anoda D203 = 3.4 Volt Lepaskan
D203
D607 Tegangan 190V Anoda
D607 = 3.4 Volt Lepaskan D607
D604, Q603 Heater / X-ray Anoda
D604 = 3.4 Volt
Collector Q603 = 3.4 Volt Lepaskan
D604
Lepaskan Q603
D601 ABL / X-ray Anoda D601 =
3.4 Volt Lepaskan D601
Q501 Tegangan Supply Vertikal
Collector Q501 = 3.4 Volt Lepaskan
D501
Menggunakan IC IX 2938CE,
TB1226
Masukan Proteksi Detektor Yang
Dideteksi Tegangan Normal
Menonaktifkan Proteksi
Pin No.30 IC1001 (5,1 V) D616
Tegangan 9V Anoda D616 = 5.1
Volt Lepaskan D616
D607 Tegangan 180V Anoda
D607 = 5.1 Volt Lepaskan D607
Q607 Heater / X-ray Collector
Q607 = 5.1 Volt Lepaskan Q607
D606 ABL / X-ray Anoda D606 =
5.1 Volt Lepaskan D606
D611 Tegangan 5V Anoda D611 =
5.1 Volt Lepaskan D611
D201 Tegangan 9V Anoda D201 =
5.1 Volt Lepaskan D201
Menggunakan IC IX 2694, M52340
Masukan Proteksi Detektor Yang
Dideteksi Tegangan Normal
Menonaktifkan Proteksi
Pin No.38 IC1001 (0 V) D606
Heater / X-ray Anoda D606 = 0
Volt Lepaskan D606
D616 ABL / X-ray Anoda D616 = 0
Volt Lepaskan D616
Q603 ABL / X-ray Collector Q603 =
0 Volt Lepaskan Q603
D610 Heater / X-ray Anoda D610 =
0 Volt Lepaskan D610
Chasis G2 Menggunakan IC IX
3031CE, TB1226
Masukan Proteksi Detektor Yang
Dideteksi Tegangan Normal
Menonaktifkan Proteksi
Pin No.30 IC1001 (3,3 V) D618
Tegangan 9V Anoda D618 = 3,3
Volt Lepaskan D618
D607 Heater / X-ray Anoda D607 =
3,3 Volt Lepaskan D607
Q607 Heater / X-ray Collector
Q607 = 3,3 Volt Lepaskan Q607
D606 ABL / X-ray Anoda D606 =
3,3 Volt Lepaskan D606
D611 Tegangan 5V Anoda D611 =
3,3 Volt Lepaskan D611
GA-4M Chasis, Menggunakan IC
IXB226WJ, M61260
Masukan Proteksi Detektor Yang
Dideteksi Tegangan Normal
Menonaktifkan Proteksi
Pin No.7 IC1001 (4.5 V) D605
Tegangan 185V Anoda D605 = 4,5
Volt Lepaskan D605
D608 ABL / X-ray Katoda D607 =
4,5 Volt Lepaskan D608
Q603 Heater Collector Q603 = 4,5
Volt Lepaskan Q603
D203 Tegangan 33V (Tuner)
Anoda D203 = 4,5 Volt Lepaskan
D203
D1091 Tegangan 9V Anoda D606
= 4,5 Volt Lepaskan D1091
Pin No.6 IC1001 (3.4 V)
D1010 Tegangan 15V Pin No.6
IC1001 = 3.4 Volt Lepaskan D1010
Chasis GA-6, Menggunakan IC
IXB725WJ, Chasis GA-7
Menggunakan IC IXB855WJZZ
Masukan Proteksi Detektor Yang
Dideteksi Tegangan Normal
Menonaktifkan Proteksi
Pin No.63 IC801 (4.1 V) D1005
Tegangan 9V Anoda D1005 = 4,1
Volt Lepaskan D1005
D608 ABL / X-ray Katoda D608 =
4,1 Volt Lepaskan D608
Q603 Heater Collector Q603 = 4,1
Volt Lepaskan Q603
D805, D203 Tegangan 33V
(Tuner) Anoda D805 & D203 = 4,1
Volt Lepaskan D203
D204 Tegangan 5V (Tuner) Anoda
D204 = 4,1 Volt Lepaskan D204
Pin No.7 IC801 (3.9 V) D1002
Power supply (AC-Detect) Pin No.7
IC801 = 3.9 Volt Lepaskan D1002
Pin No.8 IC801 (0.6 V) R523
Vertical Pin No.8 IC801 = 0.6 Volt
Lepaskan R523
Menggunakan IC IXC080WJN5Q
Masukan Proteksi Detektor Yang
Dideteksi Tegangan Normal
Menonaktifkan Proteksi
Pin No.63 IC801 (4.1 V)
Menonaktifkan Proteksi utama,
Lepaskan Jumper J497
D1108 Tegangan 5V Anoda
D1008 = 4,1 Volt Lepaskan D1108
D605 Tegangan 185V Katoda
D605 = 4,1 Volt Lepaskan D605
D608, D607 ABL / X-ray Katoda
D608 = 4,1 Volt Lepaskan D608
Q603, D604 Heater / X-ray
Collector Q603 = 4,1 Volt Lepaskan
Q603
D203 Tegangan 33V (Tuner)
Anoda D203 = 4,1 Volt Lepaskan
D203
D1105 Tegangan 5V Anoda
D1105 = 4,1 Volt Lepaskan D1105
Pin No.64 IC801 (3.9 V) D1002
Power supply (AC-Detect) Pin
No.64 IC801 = 3.9 Volt Lepaskan
D1002
Pin No.65 IC801 (0.6 V) R523
Vertical Pin No.65 IC801 = 0.6 Volt
Lepaskan R523
Menggunakan IC IXC688WJ / IC
IXC844WJ
Masukan Proteksi Detektor Yang
Dideteksi Tegangan Normal
Menonaktifkan Proteksi
Pin No.81 IC801 (4.1 V)
D1108 Tegangan 5V Anoda
D1008 = 4,1 Volt Lepaskan D1108
D605 Tegangan 185V Katoda
D605 = 4,1 Volt Lepaskan D605
D608, D607 ABL / X-ray Katoda
D608 = 4,1 Volt Lepaskan D608
Q603, D604 Heater / X-ray
Collector Q603 = 4,1 Volt Lepaskan
Q603
D203 Tegangan 33V (Tuner)
Anoda D203 = 4,1 Volt Lepaskan
D203
D1105 Tegangan 5V Anoda
D1105 = 4,1 Volt Lepaskan D1105
Pin No.82 IC801 (3.9 V) D1002
Power supply (AC-Detect) Pin
No.82 IC801 = 3.9 Volt Lepaskan
D1002
Pin No.83 IC801 (0.6 V) R523
Vertical Pin No.83 IC801 = 0.6 Volt
Lepaskan R523
Langganan:
Postingan (Atom)